Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Clean Custom Masking Circles With A Compass Cutter

A compass cutter turns ordinary masking tape into precise circular stencils for Gundam armor, mono-eye lenses, thruster rims, sensors, and mechanical detailing. With the right setup, it can produce cleaner curves than trying to trim tape freehand with a hobby knife.

The tool combines a pivot point with a replaceable blade, allowing you to set a radius and cut a consistent circle. It is especially useful when a kit needs repeated round markings or when commercial masking templates do not match the scale of a specific part.

The process rewards patience. A sharp blade, a stable cutting surface, and light pressure matter more than speed, particularly when working with thin tape or small-scale parts.

Choosing The Right Tools

Select a compass cutter with a firm locking mechanism and a blade holder that does not wobble. Some models include interchangeable blades or a protective cap, which is useful when moving between workbench tasks. Replace the blade as soon as it begins tearing the tape instead of slicing it smoothly.

Use low-tack masking tape designed for modeling, such as paper hobby tape or a delicate-surface equivalent. Regular household tape may leave adhesive residue or pull up paint. A self-healing cutting mat protects your workbench and gives the blade a consistent surface beneath the tape.

For very small circles, consider placing the masking tape on a piece of transfer film or a removable cutting sheet first. This makes the stencil easier to handle without stretching the tape around the edge.

Preparing The Masking Surface

Apply the tape to the cutting mat with enough pressure to prevent lifting, but do not burnish it so firmly that removal becomes difficult. Smooth out wrinkles with a clean cotton swab or the rounded end of a sculpting tool. Any crease can deflect the blade and distort the circle.

Measure the required diameter from the model part rather than relying only on kit instructions. A circle may need to overlap a panel edge slightly to protect the surrounding area. Mark the center lightly with a pencil, or use a ruler and fine guide marks outside the intended stencil.

Set the compass radius to half of the desired diameter. Test the setting on scrap tape before cutting the final mask. This quick check confirms that the tool is locked and that the blade reaches the correct distance from the pivot point.

Cutting A Smooth Circle

Place the pivot point at the marked center and keep the tool vertical. Rotate the compass cutter slowly, using gentle pressure on the blade. Several light passes are safer than one forceful pass because heavy pressure can stretch the tape, gouge the mat, or cause the pivot to slip.

Problem Likely cause Useful adjustment
Ragged outer edge Dull or damaged blade Install a fresh blade
Circle is uneven Pivot moved during rotation Hold the center firmly and cut more slowly
Tape stretches Excessive downward pressure Use several light passes
Mask lifts while cutting Surface is dusty or poorly secured Clean the mat and smooth the tape
Paint creeps beneath the edge Mask was not sealed Apply a thin clear coat or base-color mist

After completing the cut, inspect the edge before lifting the stencil. If a small section remains attached, finish it with a sharp hobby knife rather than forcing the tape away. Keep the circular offcut as well; it can serve as a mask for the opposite effect, such as painting a colored center inside a ring.

Transferring The Circle To A Model

Before applying the mask, clean the painted surface with a soft cloth to remove dust and fingerprints. Use tweezers to lift the tape, supporting the circle from underneath whenever possible. Avoid pulling from one side, since thin masking material can deform into an oval.

Position the mask over the part by checking several reference points around the circumference. On curved armor, press the tape down from the center outward with a cotton swab. If the surface curves sharply, cut a few tiny relief slits around the outside edge, stopping short of the painted area.

Seal the perimeter with the underlying color or a very thin layer of clear varnish. This fills microscopic gaps along the tape edge. Once dry, apply the new color in light coats, spraying or brushing away from the mask edge to reduce buildup.

Building Multi-Color Circular Details

For a concentric marking, cut each ring at a separate radius and paint from the lightest color toward the darkest. Allow each layer to cure before placing the next mask. A circle mask can also create warning bands, lens borders, and inset mechanical plates when combined with narrow strips of tape.

Remove masking tape while the final coat is slightly cured but not fully hardened. Pull it back over itself at a shallow angle. If the paint film bridges the edge, score the boundary gently with a sharp blade before peeling.

Announcements about community events and modeling discussions can be found in the forum announcements, where builders may also share techniques for paint separation and masking experiments.

Recommendations For Reliable Results

A repeatable workflow makes small circular details easier to manage:

  • Test every radius on scrap tape before cutting the production mask.
  • Replace the blade when it begins dragging, tearing, or leaving fuzzy edges.
  • Use low-tack tape and reduce adhesion further by touching it briefly to clean skin.
  • Seal the mask edge with a thin layer of the color underneath.
  • Photograph the stencil and paint sequence when a design may need to be repeated.

Keep a small record of the compass setting, tape type, paint colors, and drying times. This is valuable when matching markings across left and right shoulder armor or recreating a design after a repair.

If a circle must wrap around a compound curve, divide the design into smaller mask segments instead of forcing one flat piece to conform. Slight overlaps are easier to correct than wrinkles that allow paint to bleed underneath.

Showing The Finished Detail

After removing the mask, inspect the edge under bright light and correct tiny flaws with a fine brush or carefully trimmed paint. A satin or gloss clear coat can unify the finish, while a final matte coat helps integrate painted circles with the surrounding armor.

Finished custom markings are worth documenting from several angles. Add your completed build to the Display Case gallery to share the result, compare masking approaches, and give other builders a useful reference for their own Gundam projects.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.