Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

How To Rescue A Kit When You Break A Peg During Assembly

A broken peg can turn an enjoyable Gunpla session into a frustrating pause, especially when the damaged part belongs to a shoulder, hip, knee, or backpack connection. The good news is that most snapped pegs are repairable with patience, careful drilling, and the right adhesive.

The best repair depends on what failed. A clean break near the base may be strengthened quickly, while a peg crushed inside a socket can require part removal and replacement. Before reaching for glue, stop assembling and inspect the break under good lighting.

A calm repair also protects the surrounding plastic. Rushing to force a joint back together can widen the socket, stress thin armor, or leave a permanent mark on a finished build.

Inspect The Break Before Repairing It

Collect the broken pieces and compare them with the assembly manual. Check whether the peg broke cleanly, split lengthwise, or pulled out of its original mounting point. Look for cracks around the socket as well, since the receiving part may have taken more damage than the peg itself.

Test the fit without adhesive. If the broken surfaces meet neatly and the joint still has enough material around it, a simple reinforcement may be possible. If part of the peg is missing, the repair will usually need a metal pin or a replacement rod.

Avoid trimming damaged plastic immediately. A small fragment can help you identify the original length and diameter, which makes it easier to rebuild the connection accurately.

Choose Adhesive And Reinforcement Carefully

Plastic cement works best when the broken pieces are made from compatible polystyrene and the break is clean. It slightly melts the plastic surfaces, allowing them to fuse. Apply a tiny amount with a brush or fine applicator, press the pieces together, and let the joint cure fully before testing it.

Cyanoacrylate, commonly called super glue, is useful for mixed materials, metal pins, and repairs where plastic cement cannot create a reliable bond. It dries hard but can become brittle, so it is better paired with reinforcement than used as the only support for a heavily articulated joint.

For major load-bearing repairs, brass rod, paper clip wire, or a suitable metal pin can provide an internal spine. Select a diameter that leaves enough plastic around the drilled hole. A pin that is too thick may split the part and create a second failure.

Rebuild A Snapped Peg With A Pin

Start by flattening or cleaning both broken faces with a sharp hobby knife or fine sanding stick. Mark the center of each face with a needle or scribing tool. Accurate alignment matters more than speed, because an off-center hole can make the repaired joint sit crooked.

Drill shallow pilot holes by hand using a pin vise. Insert a short piece of brass rod or trimmed metal wire, checking the depth frequently so the drill does not break through the visible surface. Dry-fit the parts before applying adhesive and confirm that the original pose and rotation are preserved.

Once the fit is correct, glue the pin into one side first. Allow it to cure, then add adhesive to the second side and join the pieces. Leave the assembly untouched for several hours, or overnight when the joint carries significant weight. This method is especially helpful for shoulder binders, hip connectors, and backpack mounts.

Damage type Suitable repair Main caution
Clean break with full surfaces Plastic cement or super glue Allow complete curing
Peg snapped near its base Drilled metal pin and adhesive Keep the pin centered
Missing peg section Brass rod or replacement plastic rod Match the original diameter
Crushed or split socket Reinforce and rebuild the socket Do not force the joint
Peg stuck inside a part Careful extraction and replacement Protect the surrounding detail

Repair A Damaged Socket

A socket that has spread or cracked may need internal reinforcement before the peg can work again. Thin super glue can sometimes strengthen hairline cracks, but avoid flooding the cavity. Excess adhesive can reduce clearance and permanently lock the joint.

If the socket is too loose, add a very thin layer of plastic cement or super glue to the peg, let it cure completely, and sand it gradually until the fit is snug. Test often. The goal is controlled friction, not a connection so tight that the repaired peg breaks again.

When a socket has lost a large section, rebuild the missing wall with plastic sheet, epoxy putty, or a carefully shaped piece of runner. Let the material cure before refining the shape with files. Builders who are still choosing a suitable kit can also review grade trade-offs, since scale and construction style affect how demanding these repairs become.

Prevent The Same Failure During Assembly

Many peg breaks happen because a joint is being rotated while it is still too tight. Sand the peg lightly, remove mold lines, and test the movement before final assembly. A small amount of silicone lubricant can help on some joints, but apply it sparingly and keep it away from areas that will be painted.

Warm water can make some plastic parts slightly more flexible, though the temperature should remain comfortably below boiling. Never twist a joint by gripping a thin armor panel. Hold the strongest section close to the connection and move it with short, gentle motions.

These habits are useful with pre-finished products as well. If a kit includes painted or coated parts, consult this pre-painted kit advice before sanding or applying chemicals, since surface finishes may react differently from bare plastic.

Share The Repair And Preserve The Build

Photograph the broken area before and after the repair. A clear record can help you remember the pin size, adhesive, and drilling depth if another joint needs similar work later. It can also help other builders identify the safest fix for a matching kit.

When a repair is unusual, post the process in the Gundam Eclipse community with the kit grade, affected part, and tools used. Fellow builders may know of replacement runners, compatible option parts, or a less invasive method. For direct site-related questions, you can also contact the community.

A broken peg does not have to end a build. Set the parts aside, plan the repair, and share your finished result in the Display Case or forum so another builder can turn a frustrating accident into a manageable technique.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.