Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

How to Fix a Floppy Ankle Joint on Older MG Kits

Older Master Grade kits can develop loose ankles after years of posing, transport, or repeated articulation. A floppy ankle joint makes the mobile suit difficult to balance and can cause heavy weapons, shields, or oversized backpacks to pull the model off-center.

The good news is that most ankle problems are repairable without replacing the entire foot assembly. The key is to identify whether the weakness comes from a worn ball joint, an enlarged socket, a loose hinge, or stress around the ankle armor.

Work slowly and test the fit often. A small amount of added friction is usually enough, while too much material can split a socket or make the joint seize.

Diagnose the joint before modifying it

Start by removing the foot and ankle armor if the kit allows it. Examine the joint under bright light and move it through its full range. Look for white stress marks, cracks, distorted plastic, or a ball that visibly shifts inside the socket instead of rotating smoothly.

Older MG kits may use ABS, polystyrene, polycarbonate, or a mixture of plastics. The material matters because some hobby paints, lacquers, and strong solvents can weaken certain parts. If the joint is cracked rather than simply loose, friction treatment alone may produce a temporary repair.

Check whether the looseness comes from the ankle ball, the socket, or the frame connection above it. Hold each surrounding piece while moving the joint. This isolates the exact source of movement and prevents unnecessary modification to parts that are still tight.

Select a repair method that matches the damage

For mild looseness, a thin coat of clear acrylic varnish, floor finish, or hobby joint-strengthening product can add friction. Apply it to the ball or peg, allow it to dry completely, and test the fit. Several thin coats are safer than one thick layer.

For a socket that has visibly widened, a small piece of plastic, masking tape, or thin adhesive-backed film can provide a shim. Cut the material neatly, place it inside the socket, and trim away anything that prevents the parts from closing properly. This method is reversible and useful when you want to preserve the original joint.

A more permanent fix involves carefully adding a small amount of cyanoacrylate glue to the ball or peg. Let the glue cure fully, then sand it smooth before reassembly. Never apply wet super glue and force the joint together, because it can bond the pieces permanently.

Prepare the parts and tools

Gather a hobby knife, fine sanding sticks, tweezers, a small file, cotton swabs, and a light source. Keep a small amount of masking tape nearby for temporary shims. A pin vise can help if a damaged hinge needs reinforcement, though most loose ankle joints do not require drilling.

Clean dust, mold-release residue, and old lubricant from the joint before applying anything. Isopropyl alcohol on a cotton swab can remove surface grime, but test it on a hidden area first. Do not sand aggressively; removing too much plastic can turn a manageable problem into a replacement job.

Symptom Likely cause Suitable first repair
Foot droops under its own weight Worn ball or peg Thin clear coat
Joint slips from a pose Enlarged socket Plastic or tape shim
Movement feels gritty Dust or damaged surface Clean and lightly sand
White stress marks appear Excessive force or brittle plastic Inspect for cracks
Joint will not hold after coating Severe wear or split socket Replace or reinforce part

Rebuild the ankle with controlled friction

If you are using a clear coat, brush a very thin layer around the contact area rather than covering the entire joint. Let it cure according to the product instructions, then test the part gently. Add another coat only if the ankle still collapses under the model’s weight.

For a super glue repair, place a tiny drop on scrap plastic first and use a toothpick to transfer a controlled amount. Keep glue away from visible armor, polycaps, and moving surfaces that should remain flexible. Once cured, sand high spots gradually until the ball enters the socket with firm resistance.

A cracked socket may need reinforcement from the inside. A small strip of styrene can support the damaged wall, while a replacement polycap may restore the original range of motion. Avoid flooding the area with glue, since excess adhesive can make later maintenance impossible.

When reassembling the foot, do not force the ankle armor into a position that twists the joint. Confirm that the armor has clearance throughout the intended pose. Sometimes what appears to be a weak joint is actually armor rubbing against the frame and pushing the foot sideways.

Check balance and finish the repair

Place the repaired kit on a flat surface without its action base. Test neutral standing, a wide stance, a kneeling pose, and a pose with the shield or rifle attached. If the ankle holds these positions for several minutes, the repair is likely strong enough for normal display.

Inspect the surrounding plastic for scuffs caused during disassembly. Sanding marks can be refined with progressively finer abrasives, while small polished areas may be blended into the finish. If clear parts were scratched during the process, these transparent part techniques can help restore their appearance.

Keep the ankle slightly tighter than necessary when the model carries heavy equipment, but avoid making it rigid. A joint that cannot move will transfer stress into the frame and armor during posing or storage.

Use a repeatable repair routine

  • Photograph the original joint before disassembly so you can restore its orientation.
  • Clean and inspect every contact surface before adding material.
  • Begin with the least permanent method, such as a thin clear coat or shim.
  • Test the finished repair with the model fully equipped.
  • Store the kit in a neutral pose when it will not be displayed for a long period.

Share the finished build

A repaired ankle can make an older MG feel stable and enjoyable again without sacrificing its original design. Record which material you used, how many coats were needed, and whether the joint supports heavy accessories. Those details can help other builders choose a safer fix for the same kit.

After the repair holds, add the model to the Display Case gallery and include a close-up of the ankle work. Sharing the result gives other Gundam builders a useful reference and keeps practical restoration knowledge in the community.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.