Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Seamless paint layers on Gundam kits with gloss control

A smooth paint job on a Gundam model depends less on a single perfect spray session and more on how each layer supports the next. Primer, color coats, gloss varnish, panel lining, decals, and weathering all interact, so an uneven surface can become increasingly visible as the build progresses.

Gloss coating between layers is especially useful when you want clean color separation, sharp panel lines, and a polished finish without ridges around decals or paint transitions. The key is to treat every coat as a controlled surface treatment rather than simply adding more material.

This approach works for airbrushed and hand-painted kits, from small entry-level High Grade builds to complex Master Grade projects. With proper drying time, careful thinning, and light application, a seamless finish becomes much easier to repeat.

Why gloss helps between paint layers

A gloss varnish dries into a relatively level surface with fewer microscopic pores than a flat coat. This reduces the amount of pigment or panel-line wash that settles into unwanted texture. It also helps decals conform to the plastic, limiting silvering caused by trapped air beneath transparent film.

A clear layer can protect an earlier color from enamel or oil-based products, too. For example, a cured lacquer or acrylic gloss barrier may allow you to apply a contrasting wash and remove excess product with less risk to the base color. Always test the combination on a spare part, since paint chemistry varies between brands.

Gloss is not a substitute for preparation. If the underlying paint has dust, orange peel, fingerprints, or thick edges, the clear coat may preserve those defects rather than hide them.

Preparing the surface for a continuous finish

Begin by removing mold lines and seam irregularities before priming. Use progressively finer sanding abrasives, then wash the parts with mild detergent and let them dry fully. A clean surface gives primer a stronger bond and prevents oily residue from creating fisheyes in later coats.

Apply primer in several mist coats instead of one heavy pass. Once it cures, inspect the part under a bright lamp and feel it with a fingertip. Correct scratches or raised edges before moving forward. Keeping notes and photos in a work-in-progress log can make it easier to identify which preparation steps produced the cleanest results.

Choosing products and planning the finish

Use paints and clear coats that are chemically compatible, or allow generous curing time when crossing product types. Lacquer paints often provide a tough foundation, while acrylics can be convenient for detail work and hand painting. The label’s recommended thinner ratio is a starting point, not a fixed rule; spray pressure, nozzle size, and climate all affect the result.

Aim for a wet-looking surface without allowing the varnish to pool around panel lines or edges. The following sequence offers a practical guide for a painted Gundam kit:

Stage Recommended finish Main purpose Common caution
Primer Satin or smooth matte Reveal flaws and unify adhesion Avoid flooding recessed detail
Base color Satin or semi-gloss Build opaque, even coverage Use several thin coats
Intermediate clear Gloss or semi-gloss Protect paint and smooth texture Allow the color to cure first
Panel lining and decals Gloss surface Reduce staining and silvering Remove excess wash carefully
Final clear Matte, satin, or gloss Set the visual style and protect work Spray light coats to prevent frosting

A semi-gloss intermediate layer can be a better choice when a fully glossy surface makes handling difficult or when you want moderate weathering grip. The final varnish determines the character of the model: gloss suggests polished armor, satin resembles maintained equipment, and matte supports a field-used appearance.

Spraying gloss without creating ridges

Set the airbrush to a moderate pressure and begin with a light tack coat. After a short pause, add a second pass that looks evenly damp from the viewing angle. Keep the airbrush moving before pressing the trigger and release paint before stopping the motion. This prevents heavy spots at the start and end of each stroke.

Spray from several angles, but avoid repeatedly crossing the same area while it is still wet. Pay attention to corners, thruster wells, and the backs of armor plates, where clear coat can accumulate. If the finish turns cloudy, stringy, or rough, stop and let it cure rather than trying to repair it immediately with additional solvent.

Temperature and humidity affect drying. In damp conditions, lacquer clear may blush and acrylic varnish may remain soft. A clean spray booth, stable room temperature, and a dust-free drying box can make the final surface much more predictable.

Smoothing defects between coats

If a clear layer has minor texture, let it cure completely before correction. Very fine sanding film or polishing compound can level dust specks and orange peel, but use gentle pressure and avoid cutting through corners. After polishing, remove residue with a soft brush or lint-free cloth before spraying again.

For a visible step between two colors, do not rely on gloss to bury it. Feather the edge with careful sanding, restore the color in thin passes, and then apply clear coat again. Raised masking tape edges can be reduced by spraying the lighter color first, sealing the tape edge with a thin coat, and removing the mask while the paint is firm but not fully brittle.

The same principles apply when a kit becomes part of a larger scene. Studying this shoebox diorama guide can help you plan how clean armor finishes transition into dusty bases, chipped surfaces, and environmental weathering.

A reliable layer-by-layer routine

A repeatable process is more valuable than chasing a particular brand or pressure setting. Before coating a complete assembly, test the sequence on a runner or spare armor part. This reveals reactions between products and shows whether the final sheen matches the intended display style.

Keep each layer thin enough to preserve panel lines and articulation. Allow extra curing time before masking, polishing, or applying a solvent-based wash. These habits reduce rework and make a seamless paint job much easier to achieve:

  • Sand, wash, and prime every part before applying color.
  • Build opacity with several light paint coats rather than one thick coat.
  • Apply gloss only after the base color has dried and hardened.
  • Test panel liners, decals, and solvents on spare plastic first.
  • Finish with a controlled matte, satin, or gloss varnish that suits the model.

Share your finished results, coating tests, and troubleshooting discoveries with the Gundam Eclipse community. Posting clear progress photos and describing the products, thinning ratio, and drying time can help other builders reproduce the smooth finish you worked to achieve.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.