Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Building Custom Mobile Suit Camouflage With Masking Tape

Masking tape is one of the most accessible tools for adding custom camouflage to a mobile suit model. With careful planning, it can produce sharp geometric shapes, irregular field patterns, layered colors, and subtle weathered transitions without requiring an airbrush stencil or expensive aftermarket masks.

The technique works across Gunpla grades and scales, from compact High Grade kits to larger Master Grade builds. The key is controlling paint thickness, tape adhesion, and the order in which colors are applied. A little preparation prevents lifted paint and keeps the pattern integrated with the original mechanical design.

Camouflage should support the silhouette of the machine rather than hide every panel line. Consider the mobile suit’s fictional role, operating environment, and armor layout before choosing colors. A desert machine may benefit from sand, olive, and brown, while an urban combat unit could use blue-gray, charcoal, and muted off-white.

Plan The Pattern Around The Armor

Begin by deciding which parts will receive camouflage. Large shoulder armor, shields, skirts, chest panels, and leg armor provide enough surface area for clear shapes. Smaller vents and joint covers can become visually crowded if covered with multiple colors.

Use reference images for military vehicles, aircraft, or real-world combat uniforms, but adapt them to the model’s proportions. Broad diagonal bands can emphasize motion, while broken angular patches make rounded armor appear more rugged. Sketching the design on a printed photograph or spare plastic spoons can reveal problems before paint reaches the kit.

It is usually easier to apply the lightest color first and build toward darker shades. This approach reduces the amount of paint needed and makes minor tape leaks less noticeable. Keep a note of the planned sequence, especially when a pattern contains three or more camouflage colors.

Prepare Surfaces And Paint Layers

Wash unpainted parts with mild dish soap to remove mold-release residue and skin oils. After drying, lightly prime the surface if the plastic is glossy or if the paint color needs a consistent foundation. A smooth, cured base coat gives masking tape a stable surface to grip.

Allow every layer to cure fully before masking. Acrylic paint may feel dry while remaining soft underneath, and tape can pull it away in sheets. Lacquer and enamel products also require attention to compatibility, ventilation, and curing time. Test the complete paint system on spare plastic before working on visible armor.

For builders documenting a project, progress photos and pattern tests fit naturally into the Gundam Eclipse work-in-progress section, where other builders can compare masking methods and paint choices.

Choose Tape For The Surface

Low-tack modeling tape is the safest general option, especially for broad armor plates. Thin vinyl masking tape or flexible fine-line tape is useful for curves and narrow borders. Ordinary household tape can work in limited situations, but its adhesive strength and uneven edges make it less predictable.

Cut tape on a clean glass sheet with a sharp hobby blade. Fresh edges create tighter boundaries than torn or repeatedly used strips. For curved armor, use short overlapping pieces instead of forcing one long strip around the contour. Press the edges down with a cotton swab, silicone tool, or the rounded end of a clean brush.

Masking material Best use Main advantage Common risk
Low-tack modeling tape Large flat armor Reliable clean edges May lift on dusty surfaces
Fine-line tape Curves and narrow bands Flexible, sharp borders Can wrinkle under pressure
Liquid mask Small irregular sections Covers complex shapes Can leave uneven edges
Paper strips Large geometric patches Easy to cut and reposition May bleed under thin paint
Poster putty Soft organic boundaries Creates feathered edges Can leave residue

Build The Camouflage In Layers

Apply the first camouflage color across the prepared armor, then mask the sections that should remain visible. Spray or brush the next color using light coats rather than one heavy pass. Heavy paint can pool along the tape edge and create a raised ridge when the mask is removed.

When the second layer has become touch-dry but is not fully hardened, remove the tape slowly. Pull it back over itself at a low angle instead of lifting it straight upward. This reduces stress on the paint film. If the pattern requires another color, wait until the exposed layer is properly cured before adding fresh masking.

For a softer military appearance, avoid making every boundary perfectly crisp. Some sections can use slightly lifted tape edges, a thin overspray, or a narrow intermediate color. Hard edges suit angular experimental machines, while mixed edges often look more convincing on heavily used field units.

Prevent Bleeding And Paint Lift

Paint bleed usually comes from gaps along the tape edge or from applying too much paint at once. Burnish only the boundary, not the entire tape surface, and spray away from the edge when possible. A very thin coat of the underlying color along the tape line can seal tiny gaps before the camouflage color is applied.

Paint lift is more often caused by poor curing, excessive adhesive, or a glossy contaminated surface. If tape remains too aggressive, press it against clean skin or fabric once before placing it on the model. This slightly reduces tack while preserving enough grip for masking.

After removing the mask, inspect the pattern under strong light. Small flaws can be corrected with a fine brush, a carefully cut tape patch, or gentle sanding once the paint is hardened. Do not rush into weathering before the camouflage edges are stable.

Finish With Unified Weathering

A clear coat protects the camouflage and changes the visual relationship between the colors. A satin finish suits many military-style mobile suits, while a flat coat creates a more scale-appropriate appearance for dusty machines. Gloss is useful beneath decals and panel lining, but it can make the camouflage look toy-like if left across the entire model.

Panel lining should reinforce armor separation without overpowering the pattern. Use a dark gray rather than pure black on light or low-contrast camouflage. Dry brushing, chipping, pigment dust, and restrained streaking can then tie the separate patches together.

Recommendations for a controlled masking session:

  • Plan the color order and pattern on paper before cutting tape.
  • Use fresh blades and clean tape edges for sharp geometric shapes.
  • Cure each paint layer fully before applying another mask.
  • Spray several light coats instead of flooding the tape boundary.
  • Photograph the finished armor beside the reference sketch for future builds.

Custom camouflage becomes most convincing when the pattern looks functional, deliberate, and slightly varied across the machine. Share your completed mobile suit, masking experiments, or questions about paint compatibility with the Gundam Eclipse community. If you need help with a technique or project detail, the contact page provides a direct way to reach the site.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.