Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

How to Fix a Stripped Screw in a Metal Part or Action Base

A stripped screw can turn a simple Gundam repair into a frustrating test of patience. The problem usually appears when a driver slips from the screw head, when a small fastener is overtightened, or when repeated posing wears down the edges of a soft screw.

The right repair depends on where the damage is located. A damaged Phillips recess in the screw head requires a different approach from a broken thread inside a metal joint or action base. Before applying force, identify the type of failure and protect nearby armor, decals, and clear parts.

Model builders can also learn a great deal by studying how parts fit together before making repairs. A detailed review such as the HG Amazing Red Warrior can help illustrate how joints, accessories, and display connections affect maintenance.

Assess the damage before applying force

Start by removing the model from the action base if possible. Support the assembly with both hands so the damaged fastener is not carrying the weight of the kit. Use a bright lamp or magnifier to inspect the screw head, surrounding plastic, and threaded opening.

There are three common situations. The screw head may be stripped while the fastener is still intact. The screw may be seized because of paint, dust, or corrosion. Alternatively, the screw may have snapped, leaving part of its shaft inside the metal insert. Each condition needs a controlled response.

Avoid repeatedly trying the same driver. Every slip rounds the recess further and can scratch the base or deform a thin metal bracket. If the part is valuable or difficult to replace, take a quick photograph before beginning so you can document the original orientation.

Gather suitable tools and protect the kit

Use a precision screwdriver that exactly matches the screw head. A slightly larger driver can sometimes grip a damaged recess, but forcing an oversized tip may split surrounding plastic. Useful additions include a rubber band, fine pliers, a pin vise, left-hand drill bits, a small screw extractor, and replacement screws.

Place masking tape around the work area, leaving only the fastener exposed. This protects paint and prevents metal filings from settling into joints. Keep magnets, electronic components, and clear parts away from the repair if drilling becomes necessary.

For a plastic action base, reduce pressure and avoid high-speed rotary tools. Plastic softens quickly from friction, and a repair that removes too much material may leave the screw hole loose. Metal parts tolerate more force, though thin brackets can still bend.

Try the least aggressive removal method first

Press the screwdriver firmly into the screw while turning slowly counterclockwise. Keep the driver aligned with the screw axis rather than leaning it to one side. Sometimes a fresh driver and steady downward pressure are enough to release a mildly damaged fastener.

If the recess is worn, place a small piece of nitrile rubber or a wide rubber band over the screw head before inserting the driver. The material can fill tiny gaps and improve friction. This method works best when the screw is not seized and the head still has visible edges.

For a screw that extends above the surface, grip its outer edge with fine locking pliers and turn gradually. Protect painted surfaces with thin card or masking tape. Do not twist aggressively, since a small screw can snap and leave a more difficult fragment behind.

Match the repair to the fastener

Damage or condition Recommended approach Main caution
Slightly worn recess Correct driver and firm pressure Keep the tip vertical
Rounded screw head Rubber grip or precision extractor Stop if the head begins to deform
Exposed screw shaft Fine pliers or locking tweezers Avoid bending the bracket
Broken screw below the surface Pin vise or left-hand drill bit Drill slowly and centrally
Damaged threaded hole Retap, replace insert, or use a larger fastener Preserve surrounding material

A screw extractor is useful when the head is badly rounded, but select the smallest suitable size. Make a shallow pilot hole first, then turn the extractor gently. Extractors are hardened and brittle; excessive torque can break one inside the model.

When drilling out a broken screw, use a pin vise whenever possible. Manual drilling provides better control than a motor tool. Begin with a tiny bit and check alignment frequently. Once the remaining metal wall becomes thin, remove it with a needle or dental pick rather than widening the hole unnecessarily.

Repair the threads and reinstall the part

After removing the fastener, clean the hole with a soft brush and compressed air. Inspect the threads for metal debris, crushed plastic, or paint buildup. A damaged metal thread may be restored with a matching tap, while a stripped plastic hole may need a replacement insert or carefully fitted material.

Choose a replacement screw with the same diameter, thread style, and approximate length. A screw that is too long can collide with internal parts or split a plastic boss. A screw that is too short may hold temporarily but allow the joint to loosen during posing.

Before final assembly, test the screw by turning it several rotations without tightening fully. It should engage smoothly. If resistance appears immediately, remove it and inspect the alignment instead of forcing the fastener through damaged threads.

Prevent future damage during building

Good maintenance begins with controlled assembly. Use the correct driver, tighten only until the joint is secure, and avoid using a screw to pull misaligned parts together. If a model has painted surfaces or thick topcoat near a joint, clear the contact area before installation.

Sanding can also improve fit when parts are pressing against one another. The techniques in sanding curves and edges are especially useful for relieving stress without erasing panel lines or surface detail.

Keep small replacement screws in labeled containers and record their sizes. A tiny parts tray prevents fasteners from disappearing during a repair, while a magnetic mat helps keep metal screws visible. For action bases used often, inspect the connection points every few months.

Practical recommendations for a clean repair

  • Photograph the assembly before removing any parts or brackets.
  • Start with a correctly sized screwdriver and steady downward pressure.
  • Use masking tape to shield paint, decals, and transparent components.
  • Drill only after simpler removal methods have failed.
  • Test replacement screws by hand before applying final tension.

Once the repair is complete, pose the model carefully and check whether the action base remains stable under its full load. Sharing the finished result in the Display Case can help other builders compare solutions, identify compatible hardware, and learn from the repair process. Detailed notes about the screw size and method used make the post even more valuable to the Gundam Eclipse community.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.