Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Water Slide Decals On Curved Surfaces Without Silvering

Water slide decals can transform a Gundam build, adding warning labels, unit markings and tiny technical details that paint alone cannot easily reproduce. Curved armour makes the process more demanding, though: a decal may wrinkle, trap air or show a cloudy silver outline once the model is finished.

Silvering usually comes from air trapped between the decal film and the clear coat, or from a surface that is too rough for the marking to settle properly. With careful preparation, the right decal solutions and a little patience, curved shoulders, knees, shields and rounded thrusters can receive crisp markings without losing their clean finish.

Prepare The Surface Before Decalling

A smooth gloss surface is the foundation of good decal adhesion. Apply a clear gloss coat over the painted parts and allow it to cure fully. Satin or matt paint contains microscopic texture, which gives air plenty of places to sit beneath the carrier film.

Clean the part before handling it. Finger oils, sanding dust and leftover mould-release residue can interfere with adhesion. A gentle wipe with a lint-free cloth or a cotton bud lightly dampened with isopropyl alcohol is usually enough, provided the paint and clear coat have cured safely.

Australian conditions can affect drying time. A humid Brisbane or Sydney afternoon may leave a clear coat soft for longer, while a dry Adelaide day can make water evaporate quickly from the decal. Work in a clean room away from fans and direct sunlight, and give each layer extra curing time when the weather is damp.

Choose The Right Decal Size And Position

Curved surfaces reward planning. Before soaking anything, hold the decal sheet against the part and check whether the marking will cross a ridge, panel line or compound curve. Large decals are harder to conform than several smaller markings, so consider splitting a design along a panel line where the artwork allows it.

Cut close to the printed image without damaging the film. Excess carrier film is one of the main causes of visible edges and silvering. For large areas, trim the film into manageable sections or make tiny relief cuts at the outer edge. These cuts let the decal overlap a curve instead of bunching into folds.

If you are working through a large pile of kits, sensible storage helps prevent missing markings and damaged sheets; this backlog organisation guide is useful before a major decal session. Keep each sheet with its kit, instructions and spare markings in a sealed sleeve.

Soften The Decal In Stages

Use lukewarm water rather than hot water. Dip the decal briefly, then place it on a damp paper towel for a minute or two. The backing paper should slide when nudged, but the printed film should remain firm enough to handle.

Position the decal with a wet brush and avoid dragging it aggressively across the part. Once it is close to the correct location, use a soft, damp brush to push it into place. A cotton bud rolled gently over the surface can remove water and air, but pressing too hard may stretch or tear the marking.

Apply decal softener after the decal is positioned, not while it is still moving. Mild solutions are suitable for initial shaping; stronger products can be used only when needed and tested on spare markings first. As the solution works, the decal may wrinkle. Leave it alone until it settles rather than repeatedly brushing it flat.

Handle Compound Curves And Panel Lines

For a rounded shoulder or a curved shield edge, work from the centre towards the perimeter. This reduces trapped air and allows the film to follow the contour gradually. If a fold appears, lift only the affected edge with a damp brush and lay it down again instead of peeling off the whole decal.

A sharp hobby blade can help the film cross a deep panel line. Wait until the decal is almost dry, make a very light cut along the line, then apply another small amount of softener. The cut lets each side settle into the groove without pulling against the other.

Do not force a large marking over a compound curve in one piece. On a tight knee armour or domed sensor cover, several small decals may produce a cleaner result than one oversized design. This is especially useful with older aftermarket sheets, whose carrier film can be less flexible than newer releases.

Seal And Inspect The Finish

Allow the decals to dry completely before sealing them. Overnight drying is a sensible minimum, particularly in humid coastal areas. Inspect the part under a strong lamp from several angles; silvering often becomes visible only when light catches the cloudy film around the marking.

If a small silvered area remains, prick it carefully with a fine needle and apply a tiny amount of decal softener. The liquid may draw through the pinholes and improve contact with the gloss surface. Avoid flooding the area, as excess solution can stain paint or soften nearby markings.

Finish with the clear coat that suits the build. A second gloss layer can protect decals before weathering, while a final satin or matt coat blends the carrier film into the surrounding armour. Builders ordering supplies in Australia should check local stockists and postage times, as specialist decal solutions can be less readily available than paints from Bunnings or general hobby shops.

Build A Repeatable Decal Workflow

Consistency matters more than speed. Keep separate brushes for positioning decals and applying softener, change the water when it becomes cloudy, and use a fresh section of paper towel for each group of parts. Small details are easier to manage when the workbench is organised and brightly lit.

Decals often sit beside painted vents, thrusters and sensors, so plan the order of operations. Paint those small areas before applying nearby markings, and use these small-detail painting tips to avoid accidentally brushing over finished decals.

Workshop Habits That Prevent Silvering

  • Apply decals over a fully cured gloss coat.
  • Trim away unnecessary carrier film.
  • Use lukewarm water and a damp working surface.
  • Press from the centre outward with a soft tool.
  • Add softener in small amounts and let it work undisturbed.
  • Inspect under angled light before applying the final clear coat.
Surface or situation Best approach Main risk
Gentle single curve Centre the decal and smooth outward Trapped water at the edges
Tight compound curve Use relief cuts or smaller decals Wrinkles and stretching
Deep panel line Slice the film after partial drying Tearing from early cutting
Matt painted surface Add a gloss coat first Persistent silvering
Humid Australian weather Extend curing time and reduce airflow Soft clear coat and fingerprints

With a prepared surface, controlled moisture and gentle handling, curved armour becomes far less intimidating. Share your finished build, work-in-progress photos or decal experiments with the Gundam Eclipse community so other builders can compare techniques and learn from the results.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.