Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Epoxy Putty for Scratch-Building Custom Armor Plates

Epoxy putty is one of the most useful materials for turning a standard Gunpla kit into a distinctive custom build. It can create shoulder extensions, reactive armour, knee guards, skirting, vents and layered plating without requiring expensive fabrication equipment.

The process is approachable for beginners, but clean results depend on preparation and timing. Whether you build at a desk in Melbourne, a flat in Sydney or a warmer workshop in Brisbane, the same principles apply: plan the shape, control the putty, and test the fit repeatedly before committing to paint.

Choose The Right Putty

Most two-part modelling putties contain separate resin and hardener. Equal quantities are kneaded together until the colour and texture become uniform. Milliput is widely available in Australia through hobby suppliers, while Tamiya Quick Type and Apoxie Sculpt are useful alternatives when you want a finer finish or longer working time.

Read the manufacturer’s instructions before mixing. Some formulas become firm within a few minutes, while others remain workable for an hour. Warm Queensland conditions can shorten the working window, so mix smaller batches during summer. Keep unused components sealed and store them somewhere cool rather than leaving them beside a sunny window.

Plan The Armour Before Mixing

Start with a paper template or a piece of masking tape placed directly over the kit. Trace the outline, remove the tape and transfer it to thin plastic sheet or card. This gives you a repeatable guide for left and right armour plates and helps prevent a bulky addition from interfering with movement.

Consider the suit’s scale and visual language. A 1/144 kit usually benefits from shallow plates with restrained panel lines, whereas a 1/100 build can support deeper bevels, bolts and layered edges. Check shoulder rotation, waist movement and weapon clearance before adding thickness.

For reference, browse Gundam Eclipse to compare custom builds and see how other modellers balance added armour with the original kit proportions.

Build A Stable Plate Shape

The easiest method is to press a thin slab of putty onto a smooth work surface, then cut the basic outline with a hobby knife or sculpting blade. A piece of baking paper can stop the putty sticking to the bench. Use a metal ruler for straight cuts and a damp silicone tool for curved transitions.

Do not try to sculpt every feature in one batch. Make the foundation first, allow it to firm up, then add a second layer for raised sections or overlapping armour. The following guide helps match the technique to the job:

Custom feature Useful approach Main benefit
Flat shield or skirt plate Roll an even slab and cut a template Consistent thickness
Curved shoulder armour Press putty over a plastic former Controlled curvature
Raised trim Add thin putty sausages or strips Strong visual layering
Vent or recess Add a block, cure it, then carve Crisp negative space
Repeated bolts Use punched discs or cured putty dots Even detail placement

Keep a small set of sculpting tools nearby, along with water or isopropyl alcohol if recommended for your chosen product. Water can smooth some putties, but excessive moisture may make edges soft and difficult to control.

Add Panel Lines And Mechanical Details

Once the base plate has partially cured, establish bevels with a sharp blade or fine files. A shallow bevel catches paint and weathering while making the armour appear thinner than it really is. For symmetrical parts, finish one side completely, then use it as a physical reference for the second.

Panel lines should support the plate’s construction rather than cover every empty space. Use a scriber after the putty has fully hardened, taking several light passes instead of forcing a deep groove. Small plastic rod, brass wire and leftover runner can provide cleaner handles, pistons and mounting pegs than soft putty alone.

For Australian builders, local hobby shops such as Hobbyco in Sydney or Melbourne can be useful for finding scribers, sanding sticks and plastic sheet. Bunnings can also supply cutting mats, disposable gloves and fine wet-and-dry abrasive paper, although specialist modelling tools generally give better control.

Cure, Sand And Test Fit

Curing time varies, so follow the product label rather than relying on touch. A surface may feel firm while the centre remains soft. Once hardened, trim the rough perimeter, sand through progressively finer grades and inspect the part under strong light. Wet sanding helps control dust, but collect the residue instead of washing modelling waste down the sink.

Test the armour on the kit before applying primer. If the part rocks, sits too high or blocks a joint, correct it now. You can remove material with a file, or add a small mounting tab with fresh putty. Roughen the contact area and remove mould release, fingerprints and sanding dust before attaching the finished piece with plastic cement, superglue or two-part adhesive, depending on the materials involved.

Wear a dust mask when sanding cured epoxy and work with ventilation. This matters particularly in enclosed Australian hobby rooms during hot weather, when opening a window or using an exhaust fan is preferable to sanding beside the family living area.

Prime, Paint And Share The Build

Spray or brush a thin primer coat over the cured armour. Primer reveals pinholes, uneven transitions and shallow scratches that may be hard to see on bare putty. Fill defects with a tiny amount of putty or surfacer, sand again and repeat until the surface matches the surrounding kit plastic.

Paint the armour in stages if it contains overlapping plates. A darker shade in the recesses can emphasise depth, while restrained edge highlights make the silhouette readable without turning the suit into a toy-like collection of panels. Keep mounting points clean so repeated handling does not chip the finish.

Photograph the process from template to final paint and post it in the work-in-progress area. Finished photos, failed attempts and notes about products all help other builders learn, while the latest forum announcements can keep you informed about community activities and site updates. Share your custom armour plate project with the Gundam Eclipse community and give other Australian modellers a practical reference for their next build.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.