Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Building a Diorama Base from Foam Board and Plaster for Your Gundam

A convincing Gundam scene does not need an expensive resin display base. Foam board, plaster and a few common modelling supplies can create cracked concrete, a damaged hangar floor, a lunar outpost or a ruined city street. The lightweight construction also makes it easier to move your finished build between a shelf, a photo area and a local club meet.

For Australian builders, this is a practical weekend project. Foam board and plaster are easy to find at Bunnings, while hobby shops in Sydney, Melbourne, Brisbane and other cities stock terrain texture, pigments and acrylic paints. The key is to plan the scale, control moisture and build a surface strong enough to support your Gundam without warping.

Plan The Scene Around The Mobile Suit

Start with the story you want the base to tell. A standing mobile suit suits a broad, relatively flat platform, while a kneeling or lunging pose benefits from rubble, a broken wall or a raised slab. Measure the kit’s footprint and leave enough negative space around the feet so the diorama does not look crowded.

Sketch the base from above before cutting anything. Mark the Gundam’s position, the direction of travel, major debris and any support points. A 1/144 High Grade kit may work well on a base around 20 to 25 centimetres wide, while a 1/100 Master Grade generally needs a deeper platform and more substantial bracing.

Think about photography as well as display. Keep the rear wall low enough for light to reach the model, and angle large pieces so they create shadows without hiding the silhouette. If you are adapting a kit’s pose or equipment, these simple variant swaps can help match the mobile suit to the setting.

Cut And Reinforce The Foam Structure

Use 5 mm foam board for the main platform and laminate a second layer underneath if the base feels flexible. Cut with a sharp snap-off blade and make several light passes rather than forcing the knife through in one motion. A metal ruler and a cutting mat will keep edges straight and protect a workbench.

PVA glue is suitable for joining foam board, but allow each layer to dry under books or another flat weight. Avoid solvent-based adhesives, spray primers and many aerosol paints because they can melt exposed foam. For a stronger edge, cover the sides with thin card or seal them with diluted PVA before adding texture.

Foam board is light enough for a display shelf, but that can make a tall ruin unstable. Add internal braces from scrap board, or glue the structure to a thin MDF sheet. MDF is readily available in Australian hardware shops, though cutting it creates fine dust, so work outdoors or use suitable extraction.

Add Plaster Texture And Damage

Mix plaster or patching compound to a thick, spreadable consistency. Apply it in thin layers over the foam board, leaving some deliberately uneven areas for a weathered concrete finish. Press a stiff brush, sponge or coarse sandpaper into the wet surface to create pores, chips and construction marks.

For broken slabs, build up plaster around small pieces of cork, foam scraps or lightweight packing material. Score expansion joints with a sculpting tool before the surface fully hardens. Gouge shell impacts, wheel tracks and drainage channels while the plaster is still workable, then sharpen the details once dry.

Plaster can crack as it dries, especially in a hot, dry Australian summer or in a room with strong air conditioning. Let it cure gradually away from direct sun. A light coat of PVA sealer will bind loose powder and reduce chipping, but test it on spare material first.

Paint The Ground With Controlled Weathering

Prime sealed surfaces with an acrylic-compatible primer, then establish a dark brown-grey or charcoal basecoat. Concrete rarely looks like one flat colour, so layer muted greys, warm dust tones and small areas of green or rust. Dry-brushing catches raised texture, while thin washes settle into cracks and panel lines.

For a Gundam hangar, use cool greys, hazard stripes and restrained oil stains. A desert colony can use tan pigments around the feet and lower walls. Urban rubble benefits from varied masonry colours, broken signage and a few bright accents that echo the mobile suit’s armour without competing with it.

Australian light can make colours appear harsher in photographs, particularly near a bright window in Perth or Adelaide. Take test photos under the lighting you normally use and adjust the final weathering accordingly. Seal the finished base with a clear acrylic varnish, choosing satin for concrete and matt for dusty ground.

Finish, Compare And Display The Diorama

Before fixing the Gundam permanently, test the stance and check that both feet sit level. Brass rod, clear acrylic rod or discreet magnets can provide extra security for a jumping pose. Keep the attachment point hidden behind rubble or inside a damaged floor panel.

Wear eye protection and a properly fitted particulate mask when sanding plaster or MDF. Australian work health and safety guidance places emphasis on controlling airborne dust, so ventilation, vacuum extraction and careful cleanup are worthwhile. Do not sweep fine plaster into the air, and follow local council rules when disposing of dusty waste.

A Practical Materials Checklist

Core supplies

  • Foam board, scrap card and a thin MDF backing
  • Plaster or lightweight patching compound
  • PVA glue, acrylic primer and acrylic paints
  • Craft knife, metal ruler, cutting mat and sculpting tools

Useful finishing details

  • Cork, sand, gravel and broken sprue for rubble
  • Pigments, sponge pieces and stiff brushes
  • Brass rod or magnets for pose support
  • Matt or satin acrylic varnish
Base approach Weight Best use Main advantage Main caution
Single foam board Very light Small HG scenes Fast and inexpensive Can flex
Laminated foam board Light General display bases Stronger platform Needs careful drying
Foam board over MDF Medium Tall ruins and MG kits Excellent stability MDF creates dust when cut
Plaster-heavy build Medium to heavy Cracked concrete and rubble Rich surface texture May crack or become fragile

Share progress photos as the plaster dries, then add the completed scene to the Gundam Eclipse Display Case for feedback from other builders. If you need advice about materials, posing or repairs, contact the team and keep the finished base part of the community’s growing reference library.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.