Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Restoring Yellowed Plastic on 90s Gundam Kits

Yellowed plastic is a familiar problem on vintage Gundam kits from the 1990s. White armour can turn cream, pale grey parts may develop an uneven tan cast, and clear pieces can lose their crisp appearance after years in sunlight, smoke, dust or warm storage. The change is usually cosmetic rather than structural, so a careful restoration can bring an older build back to display condition.

The safest approach is gradual: identify the plastic, clean it properly, test a hidden area and use controlled lightening methods. Australian conditions make this especially important. Strong UV, hot sheds, coastal humidity and temperature swings in places such as Brisbane, Perth and Adelaide can accelerate discolouration or make brittle parts even more fragile.

Work out why the plastic changed colour

Most yellowing in older white ABS or polystyrene parts comes from oxidation. The plastic’s additives react with oxygen, heat and ultraviolet light over time. Nicotine, cooking residue and dust can add a surface film that makes the problem look worse, while glue marks and old paint may be mistaken for yellowed plastic.

Begin by checking the runner markings, kit age and material. A 1990s High Grade, Master Grade or No Grade kit may contain several plastics, including polystyrene, ABS, PVC and rubbery soft parts. Look for stress whitening, hairline cracks and loose joints before applying any chemical treatment.

Clean the parts before whitening

Disassemble the model as far as practical and photograph each stage. Wash removable plastic in lukewarm water with a small amount of mild dishwashing liquid. Use a soft toothbrush around panel lines, vents and behind armour, then rinse thoroughly and allow every part to dry for a full day.

Avoid boiling water, strong solvents and aggressive scrubbing. Melbourne hobbyists working indoors during a cool winter may be tempted to speed up drying with a heater, but concentrated heat can warp thin armour. A shaded, ventilated room is a better choice, especially for large, older parts.

Choose a controlled peroxide method

A common restoration method uses hydrogen peroxide to reverse some yellowing caused by oxidation. Cream developer, often sold by hairdressing suppliers, is easier to apply to individual pieces than a liquid bath. Use gloves and eye protection, spread a thin and even coat, then cover the part with clear plastic film to reduce drying.

Hydrogen peroxide can produce uneven results if one area receives more light or cream than another. Rotate pieces regularly and inspect them rather than leaving them unattended for hours. A low-strength solution and several short sessions are safer than a single aggressive treatment.

Treat Australian sunlight with caution

Direct Australian sun is powerful, particularly in Queensland, Western Australia and the Northern Territory. It can speed up peroxide treatment, but it can also soften parts, fade decals and create patchy results. A UV lamp with a timer gives more consistent control, while indirect daylight is suitable for a slower process.

Do not leave a restoration session on a windowsill while you head out for a cuppa. Keep the work area away from children, pets and food preparation spaces, and label any container clearly. Once the colour improves, wash the part thoroughly to remove all residue and let it dry before reassembly.

Know when to stop

Some yellowing is deep within the plastic and will only improve partially. Excessive treatment may leave a chalky surface, cause colour differences between adjoining parts or expose stress marks that were previously hidden. Test a rear-facing edge or inner armour panel first, and compare it with untreated pieces under the same lighting.

Clear parts deserve extra caution. Peroxide can cloud or weaken transparent plastic, so polishing with a specialist plastic compound is often a better first step. If a part is cracked, brittle or heavily warped, replacement may be more sensible than restoration; Australian builders can sometimes find spare runners through local hobby shops, eBay or Gumtree.

Rebuild the finish after treatment

Once the parts are clean and stable, lightly polish dull surfaces with fine sanding cloth or a plastic polish. Replace old polycaps if the joints have become loose, and inspect screws for corrosion. Reassemble slowly, checking that whitened armour has not changed size enough to affect fit.

A clear topcoat can protect the refreshed appearance, but test compatibility on spare plastic first. Matte coats hide minor variation, while satin finishes suit many 1990s kits with lightly worn surfaces. Avoid spraying in damp coastal weather, and follow the product’s ventilation guidance rather than relying on an open garage.

Photograph and share the restoration

Good photographs make colour correction easier to judge. Use a neutral background, soft light and a grey or white reference card where possible. If you need a simple setup, the guide to making a photo backdrop shows how household materials can produce cleaner, more consistent images.

When posting a work-in-progress, include the kit name, plastic type, cleaning steps, peroxide strength and treatment time. That information helps other builders understand why one method worked on a 1995 HG kit but caused problems on an older ABS frame. Australian members can also mention whether the model was stored in a shed, a sunny room or a humid coastal home.

Restoration option Best use Main risk
Mild soap wash Surface grime and smoke residue Little effect on deep oxidation
Cream developer Localised yellowed armour Patchy coverage or over-treatment
Liquid peroxide bath Several small compatible parts Leaks, uneven exposure and contamination
Plastic polish Clear parts and light haze Removing surface detail if rubbed too hard
Replacement part Brittle, cracked or badly warped plastic Colour mismatch and added cost

A restored kit does not need to look factory-fresh to be successful. Preserve its age, improve the distracting discolouration and keep original decals or weathering where they add character. Share the finished build in the Display Case gallery, and contact the Gundam Eclipse community through contact the team if you want advice on a particularly stubborn vintage kit.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.