Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Clean Airbrush Colour Changes Without Taking It Apart

Changing colours during a Gundam build should be quick, clean and repeatable. The best way to clean your airbrush between colour changes without disassembly is to flush the paint path in stages, using the right cleaner for the paint you have just sprayed. Learn more about 18732 How To Use Putty To Fill Gaps On Snap Fit Kits.

A careful routine prevents muddy mixes, blocked nozzles and wasted paint while keeping the needle, nozzle and cup assembled. It is especially useful when painting small mecha details, where several shades may be needed within one session.

Prepare The Airbrush Before Switching

Reduce the paint level in the cup first. Spray the remaining paint into a cleaning pot or onto a suitable spray-out surface, never into an open room. Wipe the inside of the cup with a lint-free swab or folded paper towel, taking care not to push fibres into the nozzle.

Add a small amount of the correct thinner or airbrush cleaner, then gently brush it around the cup walls with a soft cleaning brush. Avoid flooding the cup, as excess fluid can run backwards into the air valve or damage seals on some airbrush models.

Flush In Short, Controlled Bursts

With the airbrush pointed into a spray booth or cleaning pot, spray the cleaner in short bursts. Start with normal airflow, then briefly cover the nozzle with a cloth or nozzle cap to create a gentle backflow. This bubbling action loosens paint around the nozzle and internal cup without requiring full disassembly.

Release the nozzle before spraying again, and repeat until the spray appears clear. A long, continuous blast is less effective and creates a cloud of solvent. For builders working in a garage or spare room in Melbourne or Brisbane, good extraction matters because Australian windows and doors may not provide enough ventilation on still, humid days.

Match Cleaner To The Paint

Water-based acrylics generally respond well to their branded airbrush cleaner or a suitable acrylic thinner. Lacquer paint needs a lacquer-compatible cleaner, while enamel residue requires an enamel thinner or dedicated flush product. Never assume that one solvent is safe for every paint system, particularly if your airbrush has rubber seals.

When changing from a strong lacquer colour to a delicate pale acrylic, use an extra flush and wipe the cup carefully. Residual solvent can thin the next mix or cause it to behave unpredictably. Australian hobby shops and online retailers often stock several paint brands, so checking the manufacturer’s cleaner recommendations saves trouble when switching between Mr Color, Tamiya, AK or locally available alternatives.

Clean The Needle Without Removing It

A quick needle wipe helps remove paint that the flush cannot reach. Loosen the needle chuck slightly, draw the needle back only a few millimetres, and wipe the exposed section with a cleaner-dampened lint-free cloth. Push it forward gently again, then tighten the chuck.

Do not yank the needle out during every colour change. Repeated removal increases the chance of bending the tip or dragging paint into the rear of the airbrush. If the trigger feels rough or the spray begins to split, stop and inspect the needle rather than forcing more cleaner through it.

Use A Practical Colour-Change Sequence

For a normal switch between similar colours, empty the cup, wipe it, add cleaner, backflush briefly, spray clear and repeat once. A final small amount of thinner can be left in the cup while you prepare the next colour, but spray it out before adding paint so the new mixture is not unintentionally diluted.

When moving from dark grey to white, yellow or red, perform two or three flushes and inspect the spray-out. A faint tint means pigment remains in the cup or nozzle. The same patience helps when painting parts held with Blu Tack supports, since tiny components often reveal muddy colour contamination more clearly than larger armour panels.

Avoid Common Cleaning Mistakes

Do not use cotton buds that shed fibres, excessive pressure, or sharp tools around the nozzle. A clogged airbrush can tempt you to push a needle through the front, but that may flare or damage the nozzle. Keep a soft brush and a proper nozzle-cleaning tool nearby instead.

Never leave paint or solvent sitting in the airbrush while you take a break. In hot Australian conditions, especially during a summer session in Perth or western Sydney, residue can dry surprisingly quickly. Empty the cup and perform a short flush before stepping away, even if you plan to return in ten minutes.

Know When A Full Clean Is Necessary

A between-colour flush is designed for routine changes, not neglected paint. Disassemble the airbrush when the trigger sticks, airflow becomes inconsistent, paint leaks into the cup, or the spray remains contaminated after several flushes. These signs point to buildup around the nozzle, needle packing or air valve.

Keep your general maintenance separate from your model repair work. Before applying fresh paint to a repaired kit, for example, check the fit of a fixed polycap peg and make sure sanding dust is not entering the airbrush area. Clean tools and a tidy bench make colour changes far more predictable.

Paint change Flush routine Extra care
Similar acrylic to acrylic Wipe cup, flush, backflush, spray clear One cycle is usually enough
Dark colour to light acrylic Wipe cup, flush twice, inspect spray-out Use a lint-free cloth
Lacquer to acrylic Use compatible cleaner, then acrylic thinner Prevent solvent contamination
Metallic or heavily pigmented paint Flush repeatedly and clean the cup wall Check for pigment around the nozzle

A reliable routine keeps the airbrush ready for the next panel without interrupting the build. Share your own cleaning methods, paint tests and finished Gundam projects with the Gundam Eclipse community, and add practical bench knowledge that helps builders across Australia and beyond.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.