Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Fixing Gunpla sink marks with putty and careful sanding

Sink marks are shallow depressions left when cooling plastic contracts around thick sections of an injection-moulded part. They are common on Gunpla, especially around pegs, armour interiors, weapon grips and broad flat panels. Under strong display lighting, even a small dip can show through paint and weathering.

Using putty and sanding to fix injection molding sink marks is a reliable repair method, provided the damage is treated as a surface problem rather than covered with a large blob of filler. Careful preparation, thin applications and progressive sanding will preserve the kit’s detail and produce a clean finish.

Spotting a sink mark before assembly

A sink mark usually appears as a circular, oval or slightly irregular depression. Hold the part under a desk lamp and rotate it slowly; changing reflections often reveal flaws that are difficult to see in ordinary room light. Running a fingertip across the surface can confirm a dip, although a fingernail may catch on nearby mould lines and create confusion.

Check the part while it is still on the runner or immediately after cutting it free. A depression near a gate may be caused by a rough cut rather than shrinkage. If the area is close to a seam, test-fit the parts first, because sanding or filling before assembly can make the final alignment less accurate.

For build references and feedback from other modellers, the Gundam Eclipse community offers a useful place to compare repairs, kit versions and finished display pieces.

Preparing the plastic for repair

Remove the part from the runner with a sharp hobby nipper, leaving a small nub for a second cut. If the gate is awkward or the plastic is under stress, follow the detailed hobby saw guide before beginning surface work. A clean cut reduces the amount of filler needed later.

Wash the piece in warm water with a small amount of dishwashing liquid, then rinse and dry it fully. Mould-release residue, sanding dust and fingerprints can weaken adhesion. In Australia, a spare plastic food container makes a practical washing tub, while a sheet of newspaper or a silicone craft mat helps protect a workbench from dust.

Mask nearby panel lines with low-tack tape if the depression sits close to a sharp edge. Before applying putty, lightly scuff the hollow with 600–800 grit abrasive paper. This gives the filler a slightly rough surface to grip without enlarging the damaged area.

Choosing the right filler

For small depressions on polystyrene, hobby putty is usually the easiest option. Tamiya Basic Putty, Mr Surfacer, Vallejo Plastic Putty and similar products are commonly found through Australian model shops, specialist online retailers and some larger craft suppliers. Availability can vary between Sydney, Melbourne and regional areas, so keeping a small tube and a finer finishing product in the toolbox is worthwhile.

Use a narrow spatula, old blade or toothpick to press filler into the lowest point. Spread it slightly beyond the edge of the sink mark, but avoid covering surrounding detail unnecessarily. A thin layer is preferable to one thick application because deep putty can shrink, crack or remain soft underneath.

For larger defects, two-part epoxy putty can provide stronger support, especially on a heavy weapon or a part that will be handled often. It takes longer to cure and can obscure detail, so it is better reserved for substantial voids rather than tiny circular marks.

Applying and curing the putty

Work the filler into the depression rather than simply laying it across the top. Pressing down helps eliminate trapped air and ensures the centre is filled. Smooth the surface with a slightly damp tool where the product allows it, keeping moisture away from exposed polycaps and inner-frame materials.

Allow the putty to cure according to its product instructions. A surface that feels dry may still be soft underneath. Australia’s warmer conditions can speed up the skinning of some solvent-based products, but that does not always mean the filler has cured through. In Brisbane or Darwin humidity can also affect water-based products, so extra drying time is sensible.

Do not rush this stage with aggressive sanding. If the filler rolls, gums up the abrasive or leaves a rubbery edge, it needs more time. Cured material should sand into a fine powder or smooth dust rather than smear across the plastic.

Sanding without losing detail

Begin with 400–600 grit paper or a fine sanding sponge, using light pressure and short strokes. Sand across the repaired area from several directions, then switch to 800, 1000 and 1500 grit for a smoother finish. A sanding stick gives better control on flat armour, while folded wet-and-dry paper can reach curved surfaces.

Keep checking the part against a strong light. If a dark ring remains around the repair, the hollow may not be completely filled. Apply a second thin coat instead of continuing to sand the surrounding plastic down. This is especially important on white, red and glossy armour, where a shallow low spot becomes obvious after primer.

For panel lines and raised borders, protect the edges with tape or use a narrow file. Lost scribing can be restored with a scriber after the surface is level. Use a soft toothbrush to remove abrasive dust, then wash and dry the part before priming.

Checking the repair before paint

Primer is the best inspection tool because it reveals scratches, pinholes and remaining dips more clearly than bare plastic. Spray a light coat rather than flooding the part. Mr Surfacer or a hobby primer can expose defects, while a contrasting grey primer makes repairs on white or pale plastic easier to read.

If a flaw remains, mark it with a pencil, sand only that area and add a small amount of finishing putty. Repeat the inspection until the primer dries evenly. Do not judge the repair under only one light source; daylight near a window and a bright bench lamp can reveal different surface problems.

Repair situation Suitable material Useful abrasive range Main caution
Tiny shallow depression Plastic putty 800–1500 grit Avoid burying nearby detail
Medium sink mark on flat armour Hobby filler or surfacer 400–1000 grit Apply in thin layers
Deep or broad defect Two-part epoxy putty 240–800 grit Allow full curing time
Damage beside a panel line Fine putty 800–1500 grit Mask and preserve the line
Final surface refinement Primer and finishing putty 1000–2000 grit Inspect before painting

With a controlled repair process, sink marks become a manageable part of Gunpla preparation rather than a reason to discard an otherwise excellent kit. Post your before-and-after work in the Gundam Eclipse Display Case or share the technique with fellow builders, helping the Australian modelling community build cleaner, sharper and more confident projects.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.