Build a Simple Cardboard Lightbox for Better Model Photos
A lightbox makes a major difference when photographing Gundam kits, resin accessories, and painted mecha. It softens harsh shadows, reduces distracting backgrounds, and gives white armour a cleaner edge. The useful part is that you can make one from a cardboard box, tracing paper, and a small LED lamp.
This project suits a workbench in a Sydney flat, a Melbourne spare room, or a hobby corner anywhere in Australia. It costs very little, uses materials available from shops such as Officeworks or Bunnings, and can be packed away when the bench is needed for other tasks.
Choose the box and materials
Find a strong, clean cardboard carton large enough for the model and your camera or phone. A box from a recent delivery works well, provided it has no deep creases, grease, or printed graphics that may reflect colour into the photograph. For a 1/144 High Grade kit, a box around 40 centimetres wide is usually sufficient.
You will need tracing paper, baking paper or thin white fabric for diffusion, a ruler, pencil, craft knife, scissors, masking tape, and a sheet of white or pale grey card for the background. Tracing paper gives a predictable result, while baking paper is a useful substitute when the local stationery shop is closed.
Use a cool-running LED lamp rather than an incandescent globe. Never place hot lighting against cardboard or paper, and avoid modifying mains wiring. Electrical work in Australia is regulated, so a battery-powered or commercially assembled USB LED light is the safer choice for a home hobby setup.
Prepare the viewing area
Close the box and place it on its side so the open face points towards you. Mark large windows on the top and both side panels, leaving a border of about five centimetres around each opening. The front remains open for the camera and for placing the model inside.
The windows do not need to reach every corner. Keeping the cardboard frame intact prevents the box from sagging and gives you surfaces where the diffusion sheets can be taped securely. For a larger Perfect Grade or diorama scene, reinforce the outer edges with extra cardboard strips before cutting.
Think about the angle of your model before making the openings. A mobile phone often sits low and close to the front, while a mirrorless camera may need more working distance. Leave enough room to move the camera without touching the lightbox.
Cut the cardboard cleanly
Place the box on a cutting mat or a thick stack of scrap cardboard. Use a metal ruler for straight lines and make several gentle passes with the craft knife instead of forcing the blade through in one cut. This produces cleaner edges and is less likely to crush the carton.
Cut out the top and side panels, then brush away loose fibres. If the box has a glossy printed interior, cover the remaining frame with white paper. Dark ink can create unwanted colour casts, especially when photographing white Gundam armour or metallic paint.
For safety, keep the blade pointed away from your hands and store it with the guard fitted. Australian households often use a kitchen bench as a temporary hobby surface, so check that the surface is protected before cutting.
Add the tracing paper diffuser
Cut tracing paper panels slightly larger than each window. Tape them to the outside of the box, overlapping the cardboard by at least two centimetres. Apply short strips of masking tape rather than one continuous strip, which makes later replacement easier.
The tracing paper scatters light before it reaches the model. This produces broad illumination instead of a small, hard hotspot. If the paper wrinkles, gently pull it flat as you tape each corner; perfectly smooth sheets are helpful, but minor creases will not ruin the effect.
Leave the front open and place the white background card inside. Curve the card from the rear wall onto the floor rather than folding it at a sharp angle. That seamless sweep removes a visible horizon line behind the kit.
Position lights and the model
Place one LED light outside each side diffuser, slightly forward of the centre of the box. A third light above the top panel can lift shadows from the shoulders and head. Keep every lamp outside the cardboard enclosure, with airflow around it.
If the model looks flat, move one side light further back or lower its brightness. If one side is too dark, add a piece of white foam board opposite the brighter lamp as a reflector. This is often enough without buying another light.
For examples of how small details deserve careful presentation, compare your setup with the close-up thinking shown in Moon Gundam articulation. A lightbox is especially useful for showing joint movement, surface detail, panel lining, and careful seam work.
Tune the camera settings
Set the phone or camera to avoid automatic exposure shifts where possible. Tap the model’s main armour area, reduce exposure slightly if white surfaces are losing detail, and keep the lens parallel to the kit for a straightforward front view.
Use the lowest practical ISO and brace the camera against a small stand or stack of books. A two-second timer prevents movement when the shutter is pressed. In bright Australian daylight, close curtains or move away from a sunny window so the LED lamps remain the dominant light source.
Shoot a few test frames before posing the model permanently. Check the whites, transparent parts, beam effects, and metallic finishes on the screen at full size. A neutral white balance will usually look more natural than a strongly warm household setting.
Keep a practical photo checklist
A repeatable setup makes gallery photography faster and helps your builds look consistent from one project to the next. Check the following before pressing the shutter:
- Clean dust and fingerprints from the model.
- Straighten the background card and diffuser sheets.
- Confirm that all lamps are cool-running and stable.
- Leave enough space around the antennae and weapons.
After photographing, fold the background card separately and store the box flat if the structure allows it. Replace cloudy, torn, or yellowed tracing paper rather than compensating heavily in editing. A clean diffuser is cheaper than trying to correct uneven lighting later.
For project updates, post test images alongside your build notes in the work-in-progress forum. Showing the lighting setup can help other builders understand paint colour, texture, and scale more accurately.
A cardboard lightbox will not replace a studio, but it gives Australian hobbyists an inexpensive, controllable way to document finished kits and in-progress details. Set it beside your bench, photograph one model from several angles, and share the results with the Gundam Eclipse community.