Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Careful panel line scribing with a Dremel

A Dremel-style rotary tool can add crisp recessed detail to a Gundam kit, but it is far less forgiving than a traditional panel line scriber. The bit removes plastic quickly, and a single slip can widen a seam, flatten an edge or leave a gouge that is difficult to repair.

Used at low speed with light pressure, the tool is useful for deepening existing mould lines, opening broad access panels and creating controlled grooves in thick armour parts. The safest approach is to treat it as a precision cutting tool rather than a fast carving machine.

Method Best use Main advantage Main risk
Rotary tool with small cutter Broad or deep panel channels Removes material quickly Wandering or melting plastic
Hand scribing tool Fine straight lines Excellent control Slower on thick parts
Hobby knife Short edges and corners Easy to guide Slips and uneven depth
Chisel or file Cleaning and squaring grooves Refines the cut Can widen narrow details

Prepare the part and work area

Wash the runner oil and handling residue from the part, then let it dry completely. Assemble the armour temporarily where possible, because a panel line that looks correctly placed on one piece may disappear beneath another section. Use a pencil, 0.3 mm mechanical pencil or fine masking tape to mark the route.

A stable bench matters more than high-end equipment. Australian builders working in a Sydney or Melbourne apartment may need a compact setup, while a garage bench in Adelaide or Perth allows more room for dust control. Clamp the part gently or hold it in a small hobby vise with soft jaws; never brace it against your fingertips while the bit is running.

Select a bit and speed

Choose a small engraving cutter, narrow carbide burr or fine diamond bit with a rounded profile. A large cylindrical burr tends to remove too much plastic, while an aggressive coarse bit can chatter across curved armour. Test the bit on spare runner material from the same kit before touching the finished part.

Start at the lowest practical speed. High revolutions create friction, melt polystyrene and throw fine dust into the groove. A battery rotary tool is convenient, but corded models sold through Australian hardware retailers such as Bunnings are also common; check that a corded unit is suitable for the local 240-volt supply and use a safety switch where appropriate.

Cut in several shallow passes

Place the bit into the marked starting point before powering on if the tool design allows it, then make a short pass with almost no downward pressure. Stop, inspect the line and repeat. Three or four shallow passes produce a cleaner channel than trying to reach full depth in one movement.

Guide the tool towards yourself only when you can clearly control the movement, and keep both hands supported on the bench. For a straight line, use a metal ruler, brass template or a strip of thin plastic as a physical guide. Do not let the spinning cutter bear hard against the guide, as it can catch and jump.

Control heat, dust and edges

If the plastic begins to smell sharp, form strings or look glossy, stop immediately and let the part cool. Reduce the speed, shorten each pass and clear the chips with a soft brush. A small vacuum nozzle positioned beside the work is better than blowing dust into the air.

Wear safety glasses and a suitable dust mask, particularly when sanding or cutting polystyrene or ABS. In a shared garage or workplace, Australian work health and safety duties require sensible control of airborne particles, rotating machinery and electrical hazards; household hobby use still benefits from the same habits. Keep loose sleeves, cables and fingers away from the bit.

Refine the groove by hand

The rotary tool should establish the channel, not complete every detail. Use a fine panel line chisel or a pointed scriber to straighten the ends and sharpen corners. A folded piece of fine abrasive paper can remove raised burrs, while a narrow file helps square a broad access panel.

For curved lines, rotate the part instead of twisting your wrist around the tool. If the groove crosses a seam or raised ridge, scribe each section separately and join them by hand. This prevents the burr from climbing over the feature and creating a visible trench.

Prime, inspect and share the build

Brush away residue, wash the part again and inspect it under primer. Grey primer reveals uneven depth, ragged edges and accidental scratches before colour is applied. Fill mistakes with a small amount of hobby putty or thin cyanoacrylate, sand flush and rescribe after curing.

Keep notes about the bit, speed and number of passes that worked. Posting those results alongside photos in the forum announcements area can help other members find relevant community activities and build advice. A close-up photograph with a ruler beside the part is especially useful when comparing line width.

A rotary tool is most effective when it supports, rather than replaces, hand tools. Share your test pieces and unfinished experiments in the work-in-progress gallery, where builders can compare techniques, troubleshoot slips and refine panel layouts together. Post your next carefully scribed part with the settings and bit you used so the Gundam Eclipse community can learn from the process.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.