Drilling Soft Plastic For Clean Metal Detail Parts
Adding metal vents, pins, rivets, weapon barrels or photo-etched components can give a Gunpla build a sharper, more mechanical finish. Soft plastic is generally forgiving, but it can also deform, grab a drill bit or split around a hole if the pressure is too high.
The key is controlled cutting rather than force. With a pin vice, a correctly sized bit and a little planning, builders in Australia can achieve clean results whether they are working on a High Grade kit at a Sydney workbench or detailing a Master Grade project in Melbourne.
| Tool or method | Best use | Main advantage | Watch out for |
|---|---|---|---|
| Pin vice | Small holes in armour and frame parts | Excellent control | Slow on thick sections |
| Micro drill set | Matching holes to fine metal parts | Precise sizing | Bits are delicate |
| Motorised rotary tool | Repeated or deeper drilling | Fast material removal | Easy to overheat or enlarge the hole |
| Scriber or hobby knife | Starting the opening | Prevents bit wandering | Too much pressure can gouge plastic |
| Brass tube or metal rod test piece | Checking fit | Confirms the final diameter | Test scraps before touching the kit |
Choose The Right Drill And Support
A hand-operated pin vice is the safest choice for most soft polystyrene and ABS parts. It allows you to feel the resistance as the bit cuts, which is especially useful near thin armour edges. A small metric drill set is practical because many metal detail parts sold through Australian hobby retailers are listed in millimetres.
Use a bit slightly smaller than the outside diameter of the part when you want a press fit. For a metal rod that measures 1 mm, begin with a 0.8 or 0.9 mm hole and enlarge it gradually. Keep the part supported on a firm cutting mat or a block of scrap wood so the plastic does not flex while drilling.
Mark The Location Before Cutting
Use a sharp pencil, drafting needle or fine-point marker to mark the centre of the hole. For repeated vents or rivets, measure from panel lines rather than relying on eyesight. A small paper template can help maintain equal spacing across shoulder armour, shields and skirt plates.
Make a shallow pilot mark with a scriber or the tip of a hobby knife. This depression gives the drill bit somewhere to seat and reduces wandering on curved surfaces. The same careful, incremental approach used when planning skyscraper puzzles works well here: establish the structure first, then commit to each opening.
Drill In Short, Gentle Passes
Hold the pin vice square to the surface and rotate it slowly between your fingers. Drill for only a few turns at a time, then withdraw the bit to clear the plastic swarf. This prevents debris from packing into the flutes and gives you regular opportunities to check the angle.
Do not lean heavily on the tool. Soft plastic cuts quickly, and excessive pressure can produce a ragged exit hole or push the bit through the opposite wall. If the hole needs to pass through a narrow part, place masking tape over the exit area or support it with scrap plastic to minimise breakout.
Refine The Opening For A Metal Fit
After the pilot hole is complete, test the detail part without glue. If it is too tight, enlarge the opening with the next drill size or gently rotate the existing bit by hand. Avoid forcing the metal component into a hole that is visibly undersized, since the surrounding armour may split.
For a loose hole, use a small amount of cyanoacrylate adhesive after the final position is confirmed. Gel CA gives more working time, while thin CA can wick into a tight joint. Keep glue away from painted surfaces where possible, and use a spare piece of runner to test how quickly your chosen adhesive cures.
Avoid Heat, Cracks And Uneven Edges
Motorised rotary tools can work, but use the lowest practical speed and brief contact. Friction may melt soft plastic, especially on white armour or thin antenna components. A hand tool is usually faster overall when the hole is small because it reduces cleanup and gives better control.
Inspect both sides of the part under strong light. Raised burrs can be removed with a sharp blade, fine sanding stick or a larger drill bit turned by hand. If a crack appears, stop drilling immediately and reinforce the rear with a small piece of styrene before continuing.
Keep A Simple Bench Routine
A repeatable process makes metal detailing less stressful and helps prevent lost micro parts. Australian builders may need to order specialist detail sets from interstate suppliers or wait for imported stock, so test-fitting carefully is worthwhile before using a rare or expensive component.
Useful habits include:
- Measure the metal part with digital callipers before selecting a bit.
- Drill a test hole in leftover runner plastic first.
- Keep a magnet or shallow tray nearby for loose screws and rivets.
- Label drill bits in millimetres rather than guessing their sizes.
When working in humid coastal areas such as Brisbane or Perth, store bits and metal accessories dry to reduce surface corrosion. Builders in regional areas can often find suitable pin vices, sanding tools and small drill sets through local hardware shops, while specialist photo-etch and brass detail parts may come from Australian online hobby stores.
Finish, Photograph And Share The Build
Once the metal parts are installed, check the model from several angles before applying paint or topcoat. Bare brass, aluminium and steel can be left visible for contrast, or primed carefully if the detail should match the surrounding armour. A tiny wash around the joint will add depth without hiding the crisp edge.
A clean close-up is useful when posting a finished kit or work in progress. Gundam Eclipse’s Display Case gallery provides a natural place to show the result, explain the drill size and invite practical feedback from other builders.
Try this method on a spare runner first, then apply it to the kit one hole at a time. Share your finished build, tool setup or a tricky repair with the Gundam Eclipse community so other modellers can learn from your technique.