Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Solder-Free LED Lighting for an HG Gundam

Installing LED lights in an HG kit without soldering is entirely practical when power, placement and wire routes are planned before glue goes on. A few warm-white 3 mm LEDs can create a convincing glow in these compact 1/144-scale models.

Use low-voltage power, secure joints mechanically and leave access for servicing. Battery holders, USB modules, conductive tape and twist connections work when each part is tested before final fitting.

Choose the power system first

Begin with the LED count, not the power supply. A CR2032 suits one or two low-current indicators, while several LEDs or a light pipe benefit from USB power or a rechargeable pack. Every LED needs current limiting; a bare LED across a battery can overheat and fail.

Power option Best suited to Main benefit Main limitation
CR2032 holder One or two low-current LEDs Compact, simple and quick Limited runtime; coin-cell handling
USB 5 V supply Several LEDs or light pipes Bright, continuous power Needs a cable and correct resistor
Rechargeable pack Multiple lighting points Reusable and tidy Needs voltage matching and secure mounting
Resistor-equipped module A simple first effect Current limiting and leads are already fitted Less freedom in LED placement

For a first build, a switched CR2032 holder and a resistor-equipped LED are simplest. A 5 V USB supply can run brighter lights, but a 3 V LED still needs a series resistor unless its module includes one. Decide where the holder, switch or cable will sit before fixing LEDs.

Australian homes use 230/240 V mains at 50 Hz and Type I plugs, so never wire the kit directly to mains. State and territory rules restrict mains alterations to licensed electricians. Use an enclosed, RCM-marked USB adaptor or battery power, and leave mains wiring untouched.

Prepare the HG kit for lighting

Many Australian hobbyists work at a garage or spare-room bench, so use a protective surface and labelled trays. Photograph each subassembly before lighting it. Common HG lighting points include the chest, eyes, cockpit and backpack, although one or two sources often create the best effect.

Test-fit each LED and keep its legs parallel; trim excess wire only after the route is settled. Do not force a 3 mm LED into a narrow runner. For a light pipe, use the smallest clear fibre the opening accepts, enlarge holes carefully and sand sharp edges.

Use two-part epoxy instead of solvent cement; cyanoacrylate can fog clear plastic, while hot glue can look bulky. Humidity or condensation in Sydney and Brisbane can interfere with epoxy, and cooler Melbourne weather can extend curing. Follow the stated cure time, and let every joint cure before handling.

Adding lights during a weekend project needs reserved cure time. This realistic weekend schedule shows how to plan preparation, assembly and drying so the LEDs are not a rushed final-hour addition.

Make reliable solder-free connections

Strip only 2–3 mm of enamel from ultra-fine enamelled wire. Hold it against an LED leg and make a tight three- or four-turn twist, then pull gently to test the joint. Cover it with short heat-shrink tubing for insulation and strain relief; ordinary tape alone is easier to dislodge.

Include a current-limiting resistor in the twist. A 3 V red or green LED drawing about 15 mA from 5 V needs roughly 150 ohms; warm-white and blue parts vary, so check their forward voltage. Pre-wired resistor packs and plug-in LED modules reduce the number of joints for beginners.

Conductive fabric tape or copper tape can form a bus bar, but the adhesive must be conductive and the contact firmly burnished. Keep bare copper away from metal frame parts and never use tape as the only strain relief. Test the full path with a battery before applying glue.

Route and conceal the wiring

Run positive and negative wires along the frame’s inner edges. Anchor them with fine cable ties or clear tape at fixed points, away from moving joints and runners. Use a small dab of epoxy for anchors, but keep it off connections that may need inspection.

For a light-pipe effect, seat the LED in an opaque chest or head cavity and let clear fibre carry the glow. A short 1–2 mm optical fibre is easier to conceal than exposed wire. Gently sand the entry point and let the epoxy cure before flexing the frame.

Many builders later try conventional wiring. For a broader view of technical hobbies, this youth radio sport overview offers an interesting parallel: guided practice can turn a small technical interest into lasting skills.

Test and troubleshoot the circuit

A basic multimeter can check continuity and supply voltage before closure. Jaycar branches in Sydney, Melbourne and Brisbane commonly carry LEDs, fine wire, heat-shrink tubing and small power modules, while online sellers fill gaps. Compare ratings and warranty terms rather than price alone.

If an LED stays dark, reverse it, check the resistor and inspect the twist under magnification. Flickering usually means a loose connection or tired battery; a glow that fades quickly suggests excess current or poor contact. Clean conductive tape with a dry cloth and remake doubtful joins.

Keep coin cells secured in their holder and cover exposed terminals with tape. Australian consumer-safety rules emphasise secure battery compartments and protection around children, while state and council arrangements determine accepted recycling. Use a battery collection or hazardous-waste facility rather than general waste.

Share the finished build

The Gundam Eclipse community is ready for the result and method. Add clear photos to a Display Case gallery post, then open a forum thread listing LED size, power source, resistor, wire route and adhesive. Specific measurements help another builder reproduce the effect without repeating mistakes.

Label the thread so lighting enthusiasts can find it and answer questions with measurements rather than guesses. Post the build log, credit what worked, and invite another builder to try the same solder-free approach.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.