Epoxy Putty for Custom Gundam Collar and Skirt Armor
Epoxy putty gives Gundam builders a practical way to sculpt a custom collar or skirt armor, turning a plain kit into a convincing custom build with raised edges, layered skirts and sharp panel breaks that injection-moulded runners rarely provide. Its rigidity also makes it useful for reinforcing thin areas before painting.
Used well, the compound fills gaps, repairs stress points and accepts sanding almost like plastic. The key is to use a modest quantity, respect the product’s cure chemistry and preserve enough original detail for the eye to recognise the machine.
Compare your options
Before committing to a compound, compare the proposed shape with alternatives. A broad armor panel may need a plastic core, while epoxy is better for local depth, joins and reinforcement.
| Method | Best suited to | Strengths | Limitations |
|---|---|---|---|
| Epoxy putty | Deep relief and reinforcement | Strong, sandable, bonds well | Mixing and full cure take time |
| Styrene cement | Hairline joins | Fast and nearly invisible | Limited thickness and slower handling |
| Plastic card | Broad new panels | Lightweight and easy to modify | Requires careful bonding and shaping |
| Polyester putty | Small surface shaping | Easy to sand and smooth | Less rigid and less durable on edges |
Choose epoxy putty when the custom element needs mass or a defined edge. For a large skirt extension, combine it with sheet plastic or a printed template; relying on bulk putty alone can make the model heavy, slow to cure and difficult to repair.
Prepare the base armor
Start by assembling and fitting the stock armor, checking seams, alignment and clearance around the waist joint. Photograph the silhouette from front, side and rear, then mark where the collar rises or the skirt should sweep backward.
Before adding thickness, study the surface language on the original kit. This HG Red Warrior review is a handy example of how panel lines, vents and colour breaks can guide a believable redesign rather than a bulky lump.
Clean the bonding area with a plastic-compatible degreaser, abrade glossy paint lightly and score large contact zones. Mask adjacent surfaces, because a clean original finish is much easier to protect than an epoxy stain scraped away later.
Mix and apply epoxy putty
Use fast-curing putty for small test shapes, but allow the final joint to cure fully before flexing the build. Knead equal portions only if the manufacturer specifies a one-to-one ratio; one-part polyester filler and two-part epoxy putty are not interchangeable.
Prepare only enough for one session and keep batches thin enough to warm in the centre. Borrow the discipline of a range safety checklist: organise tools, label compounds and confirm curing conditions before beginning.
Wear nitrile gloves, eye protection and suitable respiratory protection when sanding cured dust. Follow the safety data sheet, ventilate the room and wash skin promptly; epoxy allergens and silica-bearing dust deserve more care than a hobby table usually gets.
Shape the collar and skirt armor
Build the collar from its inner surface outward. Add a thin centre layer, cure it, then introduce the V-shape, raised edges and small vents as separate additions. Working in stages keeps the shape symmetrical and prevents trapped putty from forcing the collar open.
For skirt armor, establish a plastic or card template from the front and side views. Extend the lower edge, thicken the hem and carry existing panel lines across the new surface. Leave a little extra material for final correction, especially around the central skirt blades.
Sand, prime and paint
After full cure, establish the silhouette with 180–320 grit paper, moving to 400–800 grit for shaping and 1200 grit before primer. Sand across the fillets rather than chopping flat sections, and check constantly against the untouched kit.
Fill pinholes with thinned filler or fresh putty, repeating the sanding after each cure. If a recipe looks unusual, cross-check it against the manufacturer’s instructions and an independent technical reference before mixing.
Use a suitable primer to reveal defects, then paint with the same base colours as the surrounding armor. Thin decals or colour masks can suggest fabric, ceramic or metal without turning the custom area into a separate visual block.
Handle Australian workshop conditions
Australian conditions affect the schedule more than builders expect. Brisbane warmth can set a skin before the centre cures, humid Sydney afternoons can complicate primer and paint, Melbourne’s variable temperature can fool you about cure time, and a cold Canberra winter may extend the wait. Builders who reserve Saturday for the bench should start long cures early enough to leave time for sanding and paint.
Australian hobby markets centred on Sydney, Melbourne and Brisbane offer several filler choices, while specialist sellers such as Oz Modeller, BuyRads and Spartan Hobby broaden the range. Compare AUD prices including the 10% GST, and factor in Australia Post or courier delivery for imported putty.
For workplace or commission builds, follow state and territory work health and safety laws, GHS labels and the product safety data sheet. Do not pour mixed epoxy or solvent into stormwater; local council rules and the SDS determine disposal, while hobbyists should keep containers sealed and separate.
Document and share the result
Record the compound, mix ratio, cure time, grit sequence and any heat used. Those notes turn a successful custom piece into a repeatable method, and they help another builder distinguish a sound technique from a result that only looks good after rushed sanding.
When the build is ready, post clear front and rear photographs in the Display Case or a technique thread, then flag the project in the community announcements. Explain what changed, where the putty was added and which stage needed revision so feedback reaches the builder and the wider modelling community.