Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Matte, Semi-Gloss and Gloss Topcoats Compared

A topcoat controls how light moves across a finished Gundam model. Matte diffuses reflections, semi-gloss creates controlled lustre, and gloss produces sharp highlights and richer-looking colour. Builders can compare methods, photos and practical advice through the Gundam Eclipse community, where the same kit can look very different under display lighting.

Sheen also changes which flaws are noticeable. Panel lines, sanding marks, fingerprints, brush texture and orange peel read differently at each level of reflection. A flat surface can give a simple build a purposeful military look, while a high-gloss clear coat can make careful colour matching and metallic finishes feel vivid.

Australian conditions deserve attention. Sydney’s humid, salt-laden coastal air, Brisbane’s heavy summer humidity and Melbourne’s changeable weather can influence drying, dust and handling. Perth and Adelaide often bring intense heat and strong UV, so a finish that looks crisp on the bench may behave differently after transport or months on a shelf.

Start with the effect you want, then check how the manufacturer names it. Paint labels are not standardised: one brand’s matte may be another brand’s satin, and semi-gloss descriptions also vary. A test card made with your primer, colour and intended clear coat will settle the choice without committing an entire panel.

How sheen changes a model

Matte topcoat scatters light rather than returning a clear image of the room. This low-reflection finish suits stealth armour, worn machinery and restrained display pieces. It also softens tiny irregularities, although poorly prepared surfaces can still show as rough patches once the paint is lit from the side.

Semi-gloss sits between flat and wet-looking finishes. Its moderate lustre gives colour depth without the intense mirror effect of gloss, making it a practical choice for many mobile suits. Gloss reflects distinct light sources, often making metallic paint and sharp panel-line contrast more prominent; it is equally unforgiving of dust, uneven coats and fingerprints.

Choosing a finish for the effect

For a competition-style display piece or a clean hero photograph, gloss can give a freshly built model visual impact. Matte works well when realism comes from grime, subdued colours or a factory-like surface. Semi-gloss offers a balanced compromise and often suits builders who want the colour to read clearly without a mirror finish.

Surface quality matters as much as sheen. Compare moulded texture, panel-line definition and primer compatibility before painting. This recent releases overview provides context on newer positive-printed parts, although the final appearance still depends on careful preparation, thinning and application.

Preparing and spraying in Australian conditions

Work from a clean, degreased surface over fully cured primer. Test the topcoat on the exact colour scheme, and follow the can’s flash time and cure guidance; several thin, even layers generally give a more consistent sheen than one heavy coat. Use suitable ventilation and respiratory protection, especially in an enclosed garage.

Australia’s practical hobby setups often combine workshop supplies from Bunnings with specialist stock from hobby retailers such as Mary’s Models in Adelaide. Keep garage dust out, and avoid painting during hot, windy or very humid conditions when possible. In Brisbane and coastal Sydney, allow extra drying time; in dry Perth and Adelaide, dust control becomes the greater concern.

For transport, let the final coat cure fully rather than relying only on a surface-dry appearance. Heat can soften fresh plastic or lift paint if a model is packed too soon, while UV and temperature swings may alter gloss plastics over time. A rigid case with clean foam offers better protection than loose tissue or a crowded shelf.

Weathering, decals and surface protection

A topcoat can seal colour and decals, but its order in the finishing sequence changes the result. Apply clear coats after decals when maximum protection is the priority, allowing each layer to cure before the next. If panel-line washes or pigment effects go on afterwards, use paint thinners compatible with the acrylic finish so the gloss layer does not cloud or dissolve.

For deliberate battle damage, work after the base finish has hardened. The soldering iron damage guide demonstrates a heat-based effect on Gundam parts, but the method belongs on a sacrificial test piece and demands ventilation, an extinguisher and a heat-resistant work area. Acrylic-based chipping colour can provide similar exposed-metal marks without heat.

Finish comparisons at a glance

The practical choice comes down to reflection, the condition of the model and the display environment. Gloss demands the cleanest surface and strongest lighting; matte forgives minor defects; semi-gloss remains versatile.

Finish Surface character Strongest use Main drawback
Matte Low, diffuse reflection and soft highlights Stealth, weathered and utilitarian models Uneven coats can read as patches
Semi-gloss Moderate lustre and balanced colour depth General-purpose display and mobile-suit builds Brand labels vary, and flaws may sit between visible and hidden
Gloss Sharp highlights with strong colour and metallic impact Hero shots and clean show pieces Shows dust, fingerprints, orange peel and brush texture

Test under the lights you actually use. A finish photographed beneath bright LEDs may behave differently at a Melbourne show stand or in a dim display cabinet. The brand and application method matter, so treat these categories as guides rather than fixed formulas.

Share the result with other builders

Choose the finish that supports the story of your build, make a small swatch and document the result under neutral light. A clear photo of the same panel in matte, semi-gloss and gloss can help another modeller compare surface quality, colour depth and dust behaviour before starting a larger project.

Post your swatch, work-in-progress photos or finished model on Gundam Eclipse, include the topcoat used, and invite others to suggest adjustments for Australian conditions. Share what you learned about thinning, cure time, decals or weathering so the next builder can begin with practical knowledge.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.