Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

How to assemble a kit with minimal seam lines

A clean Gunpla build begins long before paint, primer, or topcoat. The way parts are clipped, fitted, and aligned has a major effect on whether armor joins disappear into the design or remain as distracting lines. With a patient workflow, even a straight build can achieve a polished appearance without extensive modification.

Seam lines are the visible gaps or raised joins left where two molded parts meet. Some are intentional panel breaks, while others cut across armor in a way that looks unnatural. Learning to distinguish between them helps you decide which areas need sanding, cement, masking, or simply careful assembly.

Choose a clean assembly workflow

Start by studying the manual and the runners before removing parts. Look for armor sections that enclose a frame, weapon barrels molded in two halves, and limbs divided along obvious vertical lines. Dry-fitting these pieces reveals whether the seam is designed to remain visible or can be eliminated.

Build in small subassemblies rather than rushing through an entire section. Complete one arm, leg, weapon, or torso block at a time, checking its fit from several angles. This keeps sanding dust away from unfinished components and makes it easier to identify the source of a misaligned joint.

Prepare parts before clipping

Use a sharp nipper and leave a small amount of runner attached to the part. Remove the remaining nub with a second cut or a hobby knife, working gradually instead of slicing deeply into the plastic. A gouged surface often requires more repair than the original seam.

Test-fit every pair before applying adhesive. If the halves do not close evenly, inspect for internal pegs, tabs, or frame pieces that may be preventing a full fit. Carefully trimming an obstructing tab can create a tighter join, but remove only a little material at a time so the connection does not become loose.

For large seams, plastic cement is usually more effective than thin instant glue. Apply a small amount along the joining edge, press the pieces together until a slight bead of softened plastic appears, and allow the area to cure fully. That bead can later be leveled to produce a continuous surface.

Align and control the joints

Good alignment is the foundation of seam removal. Hold the parts together under even pressure and check the front, back, and side profiles before the cement sets. Clips, masking tape, or gentle clamps can maintain pressure without marking the armor.

Different grades of sanding tools serve different purposes. Begin with a medium abrasive to level the raised seam, then move to finer grits to remove scratches. Sand in multiple directions only when necessary; finishing with consistent strokes along the surface helps keep the panel flat.

Builders working on complex kits can learn from RG Hi-Nu pitfalls, especially where layered armor and a dense inner frame make alignment difficult. On articulated kits, always confirm that sanding or cement has not restricted movement before moving to the next stage.

Area of the kit Common seam problem Useful approach Detail to protect
Torso armor Uneven front or back split Dry-fit, cement, then sand flat Chest vents and hatches
Arms and legs Long line across rounded armor Check frame clearance before closing Rotation joints
Weapons Barrel or handle halves Align with a flat surface as a guide Muzzles and grooves
Shields and backpacks Large symmetrical panels Use tape or clips for even pressure Mounting pegs
Small accessories Misaligned edges and nub marks Use a knife and fine sanding sponge Molded insignia

Refine visible armor surfaces

When a seam crosses a smooth armor panel, sanding alone may leave a shallow depression. A small amount of modeling putty can fill this gap, though it should be applied sparingly. Once cured, sand the repair flush and inspect it under a strong light.

Use guide tape around the repair when working close to raised details. This prevents accidental rounding of edges and protects panel lines from being erased. If a recessed line is lost, restore it with a scribing tool after the surface has been leveled.

A primer coat is an excellent inspection stage. It reveals scratches, pinholes, and uneven transitions that may be difficult to see on bare plastic. Apply a thin coat, correct the flaws, and prime again only where needed rather than burying the entire part under heavy layers.

Hide seams without losing detail

Not every seam should be removed. A line that follows a real armor break, hatch, or mechanical division can add scale and visual interest. In some cases, deepening the line with a scriber makes it appear intentional instead of trying to erase it.

Color and finishing can also reduce the visual impact of a minor join. A controlled panel wash, subtle shading, or a matte finish can unify surfaces, but these techniques should support proper construction rather than conceal poor alignment. Inspect the model before painting so structural problems are handled first.

If you plan to add custom equipment, match the surface treatment of the new parts to the original kit. The guide on 3D-printed weapon accessories offers useful direction for preparing printed components, which often need extra cleanup before they blend with injection-molded armor.

Build habits that keep seams under control

A repeatable process makes seam cleanup faster and more predictable:

  • Dry-fit every major armor section before using cement.
  • Keep sanding sticks and files clean so old plastic dust does not scratch fresh surfaces.
  • Check moving joints after each repair, especially around knees, elbows, shoulders, and hips.
  • Use primer and angled lighting to inspect repaired areas before applying color.
  • Preserve intentional panel breaks instead of treating every molded line as a flaw.

A minimal-seam build rewards patience more than force. Let cement cure, use light pressure, and make several small corrections rather than one aggressive cut. Photographing a finished subassembly for the Gundam Eclipse Display Case can also help you notice how alignment, surface texture, and seam treatment affect the model from different viewing angles.

Share your cleanest seam-reduction techniques, difficult repairs, and finished builds with the Gundam Eclipse community so other builders can apply those lessons to their next kit.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.