Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Building the MG Freedom 2.0 Without the Usual Breakages

The Master Grade Freedom Gundam 2.0 remains one of the most impressive modern Gundam kits. Its sharp proportions, layered armor, huge wings, and excellent articulation give it a strong presence straight out of the box. That engineering also makes the build more demanding than a simple snap-fit project.

Most problems come from forcing parts, skipping dry fits, or treating movable armor like fixed display detail. A careful builder can avoid nearly all serious damage by understanding where pressure builds and by testing each mechanism before applying stickers, paint, or topcoat.

This guide focuses on the common trouble spots, practical fixes, and handling habits that make the MG Freedom 2.0 more enjoyable. The same methods also apply to other complex Master Grade and Real Grade releases.

Preparing The Frame Before Assembly

Start by cleaning nub marks thoroughly, especially around the hip, waist, shoulder, and wing assemblies. A small gate remnant can prevent a part from seating correctly, leading you to apply excessive force. Use a sharp hobby knife for final cleanup rather than repeatedly twisting a stubborn component.

Dry-fit every joint that will carry weight. The hips, knees, ankles, shoulders, and wing hinges should move smoothly without feeling gritty or locked. If a joint is unusually tight, lightly polish the peg or socket with fine sandpaper. Remove material gradually; it is much easier to loosen a joint than to restore one that has become too loose.

The Freedom 2.0 has many moving armor panels that can catch against neighboring parts. Test the complete range of motion before attaching external armor. This reveals interference early, while the assembly is still easy to separate.

Protecting The Hip And Waist Connections

The hip mechanism is the area that deserves the greatest caution. The internal frame uses compact connections that can be stressed when the legs are rotated outward or when the torso is posed aggressively. Do not treat resistance as a sign that the joint simply needs more pressure.

Build the waist and hip section slowly, checking the manual diagrams for the correct orientation of every polycap and frame piece. If a leg will not insert cleanly, remove it and inspect the peg rather than rocking it from side to side. Sideways force can crack a connection or deform the socket.

When posing the completed model, support the torso with one hand while adjusting the legs with the other. Keep the hips close to their natural range unless you have reinforced or modified the frame. A stable standing pose is safer than repeatedly forcing a dramatic split-legged action pose.

Handling The V-Fin And Small Details

The yellow V-fin is thin, sharp, and easy to damage during cleanup or handling. Cut each antenna from the runner with space around the part, then trim the remaining gate carefully. Twisting the piece away from the runner can create a stress mark or snap the tip.

Before attaching the V-fin to the head, check the connection point for flash and confirm that the head crest is aligned. Pressing directly on the antenna tips is risky. Hold the thicker center section whenever you need to remove or reposition the head.

If an accident happens, a controlled repair is usually possible with a small brass pin and suitable plastic cement or cyanoacrylate. The detailed guide on repairing a broken V-fin explains how to stabilize the piece without leaving an obvious scar.

Managing Wings, Cannons, And Weapons

The wing binders add considerable weight to the backpack. Their hinges may feel tight at first, but loosening them by force can produce floppy panels that cannot hold a pose. Work each hinge through a small range, then adjust it gradually rather than swinging it through its full arc immediately.

The wing sections should be opened and closed while watching for armor collisions. Some panels overlap in ways that are easy to miss when the model is viewed from the front. If a binder shifts under its own weight, inspect the hinge for incomplete assembly before adding any joint-strengthening product.

The beam rifle, shield, and rail guns are best attached after the main body has been balanced. Heavy accessories can expose weak ankles or loose wrists. When storing the kit, remove large weapons if they pull the arms downward for long periods.

Problem area Typical symptom Likely cause Practical fix
Hip frame Leg connection feels locked or cracks Excessive force or incorrect alignment Disassemble, inspect, and polish the peg lightly
V-fin Antenna bends, whitens, or snaps Twisting during nub removal Cut away from the part and trim gradually
Wing binders Panels sag or refuse to hold position Overworked or damaged hinge Check assembly, then use minimal joint treatment
Ankles Model leans after posing Heavy backpack and wings Center the torso and adjust both feet evenly
Wrists Weapons fall from the hands Loose grip parts or excessive accessory weight Tighten the grip carefully or use a small clear shim

Fixing Loose And Tight Joints

A tight joint should be loosened in small increments. Fine sanding is usually safer than cutting, and the result should be tested after every few strokes. Keep dust away from finished surfaces and wash the part before reassembly if necessary.

For loose joints, a thin layer of hobby-safe acrylic floor finish, joint-strengthening liquid, or carefully applied clear paint can add friction. Let the coating cure completely before testing. Applying too much at once may prevent the joint from closing or create new stress during assembly.

Avoid strengthening joints that are already under structural strain. A stronger connection is not automatically safer if the surrounding plastic is thin. The goal is controlled movement, not maximum resistance.

Building A Cleaner And Safer Display Piece

Decide early whether the kit will remain a straight build, receive panel lining, or be fully painted. Paint thickness can make already-tight armor and frame connections unusable. Test painted parts before final assembly and remove excess coating from pegs and sockets where needed.

Panel lining should be used carefully around sliding armor. Enamel products can weaken some plastics if they pool in joints or remain trapped under pressure. Apply small amounts, clean excess promptly, and allow everything to dry before moving the mechanism.

For builders who want a lower-pressure project before tackling a large Master Grade, the SD EX Standard line offers useful practice in nub cleanup, panel lining, and posing. Those fundamentals transfer directly to the Freedom 2.0.

A Reliable Workflow For Future Builds

Use these habits throughout the build:

  • Read the manual fully before beginning a complex internal section.
  • Dry-fit moving parts and check for interference before applying force.
  • Loosen tight pegs gradually instead of twisting them into place.
  • Support heavy assemblies while posing or transporting the model.
  • Photograph fragile connections before disassembly so orientation is clear.

The MG Freedom 2.0 rewards patience with a highly expressive finished model. Share your build, pose experiments, repairs, and lessons learned in the Gundam Eclipse forum or Display Case so other builders can benefit from your experience and add their own solutions.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.