Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

How to use putty to fill gaps without sanding away detail

Gap filling is one of the small skills that can make a Gundam model look professionally finished. Seams around armor plates, shoulder joints, weapons, and thruster housings can distract from an otherwise careful build, yet aggressive sanding may erase panel lines, rivets, vents, and molded texture.

The solution is controlled surface repair rather than simply adding a large amount of filler and sanding until the area is flat. Choosing the right putty, applying it precisely, and removing excess before it fully hardens will preserve the surrounding detail and reduce corrective work.

This approach works for beginners and experienced builders alike. It is especially useful on high-detail Master Grade kits, customized mobile suits, and any project where sharp mechanical features need to remain crisp.

Choose a filler for the job

Modeling putty comes in several forms, and each behaves differently. Lacquer-based putty is useful for hairline seams and shallow scratches, while epoxy putty is better for sculpting, rebuilding missing material, or correcting larger gaps. Two-part epoxy usually provides more working time and shrinks less, but it can obscure detail if spread carelessly.

Water-based hobby putties are easier to clean and often suitable for small imperfections. They may be softer and more prone to shrinkage, so they are best applied in thin layers. For advanced custom work, cyanoacrylate glue mixed with talc can create a hard filler, though it sets quickly and demands careful ventilation and precise application.

Before modifying a valuable kit, study how builders handle replacement parts and surface corrections in resources such as these MG Zaku II parts tips. The same attention to fit and surface alignment applies when filling seams.

Prepare the parts before filling

Dry-fit the pieces first and inspect the gap from several angles. A seam may be caused by a misplaced internal frame, a nub, or a warped connection rather than missing material. Fixing the fit before applying putty prevents unnecessary filler and keeps the original geometry intact.

Wash away mold-release residue and handling oils, then let the parts dry completely. Lightly scuff only the inside edges of the seam if extra adhesion is needed. Avoid roughening the visible armor around the gap, since those scratches can become more difficult to remove than the original imperfection.

Mask nearby panel lines with narrow strips of low-tack tape. For vents, recessed channels, and raised borders, place the tape so only the gap remains exposed. This creates a physical boundary that helps stop filler from spreading into areas that should remain untouched.

Apply less putty than you think

Use a toothpick, fine spatula, or silicone sculpting tool to press putty into the seam. Work across the gap rather than dragging along it, which forces the material down into the joint. A thin, complete fill is preferable to a thick ridge sitting above the surrounding plastic.

Remove excess immediately with a tool lightly dampened according to the putty manufacturer’s instructions. Cotton swabs, makeup sponges, or a folded paper edge can lift material from flat surfaces before it cures. For narrow panel lines, a sharpened wooden stick can scrape away the filler while leaving the surrounding groove intact.

Allow the filler to cure fully, even if the surface feels dry. Sanding too soon can pull soft putty from the seam and create low spots. On a deep gap, use two or three modest applications rather than one heavy layer; this reduces shrinkage and makes the final surface easier to control.

Protect detail while sanding

When sanding is necessary, use small abrasive pieces rather than a large sanding block. Folded sandpaper, sanding sponges, and narrow polishing sticks can reach a seam without crossing broad areas of armor. Begin with a fine or medium grit and use light strokes that follow the shape of the part.

A useful technique is to sand only the raised putty line while checking the surface frequently under strong light. Once the filler is level, switch to a finer grit and stop as soon as the seam disappears. Excessive polishing can soften edges, so there is no benefit in continuing after the surface is smooth.

For panel lines that run close to a filled seam, deepen them before applying filler or restore them afterward with a scriber. Use a metal ruler or tape as a guide, and make several light passes instead of one forceful cut. This restores a clean channel without widening it unpredictably.

Match the method to the gap

Gap or defect Suitable filler Detail-saving approach
Hairline seam Lacquer putty or thin CA glue Apply with a needle and wipe away excess immediately
Medium armor seam Standard modeling putty Mask nearby detail and sand with a narrow abrasive
Deep or uneven gap Two-part epoxy putty Build in thin stages and shape before full cure
Small sink mark Water-based or lacquer putty Dab into the depression and level with a flat tool
Missing corner or edge Epoxy putty Sculpt the profile, then sharpen it after curing
Gap beside a vent Fine putty or dissolved plastic filler Protect the vent with tape and use a pointed applicator

Refine the surface before painting

After sanding, inspect the repair with a thin coat of primer. Primer reveals pinholes, shallow scratches, and remaining low spots that may be difficult to see on bare plastic. If flaws appear, spot-fill them rather than recoating the entire area.

Keep the primer thin around mechanical detail. Heavy layers can soften panel lines and make vents look shallow. A controlled airbrush pass or lightly misted rattle-can coat is safer than flooding the surface.

Once the repair is clean, restore any lost engraving and wash away sanding dust. Painting small features requires the same precision; these vent painting tips can help bring back contrast in areas that are easily overwhelmed by primer or paint.

Build a repeatable gap-filling routine

A consistent process makes surface repair faster and protects details on every kit:

  • Dry-fit the parts and correct alignment before reaching for putty.
  • Mask panel lines, vents, and sharp edges surrounding the seam.
  • Apply the smallest amount that completely fills the defect.
  • Remove overflow before curing, then sand with a narrow abrasive.
  • Prime the area and repeat only where flaws remain.

Keep different applicators, sanding tools, and fillers labeled in your workspace. Recording which product worked well on a particular plastic type can also save time on future builds. Gundam Eclipse’s forum announcements are a useful place to watch for community news, build events, and shared hobby discussions that may expand your repair techniques.

A clean gap repair should disappear beneath primer while the kit’s original mechanical language remains sharp. Share your finished result or work-in-progress photos in the Gundam Eclipse community, where other builders can compare methods, troubleshoot difficult seams, and help refine the next build.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.