Gundam Eclipse
Cluster of bright red ripe tomatoes on the vine against a blurred green background

A community for builders of all skill levels — share finished builds, works in progress, kit reviews, and stay up to date with forum announcements.

Browse the Display Case

Stay Connected

Get the latest from the Gundam Eclipse community delivered to your inbox.

Latest from the Forum

Gundam Eclipse is Moving!

September 26, 2018 — by tc012009

An important announcement was posted in GE Forum News regarding the future of the community. The forum had accumulated 240 topics and approximately 1,900 posts in its announcements section by this time.

  • Posted in GE Forum News
  • Final recorded announcement in the section

Moderoid 1/60 SAVAGE CROSSBOW

Using a Pin Vise For Custom Metal And Photo-Etched Parts

A pin vise is one of the most useful hand tools for adding detail to a Gundam or other mecha model. Unlike a powered rotary tool, it gives you slow, precise control when opening a hole for metal thrusters, brass rods, aftermarket weapon parts, or photo-etched add-ons.

Using a pin vise to drill holes for custom metal parts or photo-etched add-ons takes patience, but the process is approachable for beginners. With the right bit, careful marking, and support behind the plastic, you can improve a high-grade kit without cracking armour panels or enlarging holes accidentally.

Choose The Right Tools

A comfortable pin vise should hold small drill bits securely and turn smoothly without excessive wobble. A double-ended model-making handle is convenient because it keeps several bit sizes available, while a single-ended version is often easier to grip for longer sessions. Choose a set designed for hobby work rather than a general hardware set with coarse bits.

For most Gunpla modifications, bits between 0.3 mm and 2 mm cover the common jobs. A 0.5 mm bit may suit a metal rivet, while a 1 mm or 1.5 mm bit can prepare a socket for a metal pipe or larger thruster. Keep a small ruler or digital calliper nearby so the hole matches the fitting rather than relying on visual estimates.

Local Australian hobby shops such as Hobbyco in Sydney or Metro Hobbies in Melbourne often stock modelling drill sets, sanding tools, and aftermarket accessories. Bunnings can be useful for storage boxes and general hand tools, but specialist model suppliers usually offer finer bits and more suitable pin vises.

Mark And Support The Plastic

Before drilling, test the metal part or photo-etched component against the model. Study its depth, flange, and intended angle. Mark the centre with a sharp pencil, scriber, or fine-point permanent marker. For a circular fitting, a tiny indentation made with a needle helps the drill start in the correct position.

Support the panel from behind whenever possible. Blu Tack, folded tissue, or a small block of dense foam can prevent the armour from flexing. Thin parts are especially vulnerable near corners and edges, where pressure can cause a split. If the panel is removable, take it off the frame and work on a flat surface rather than drilling directly on the assembled kit.

A small pilot hole makes the final opening more accurate. Start with a bit around half the diameter of the intended hole, then enlarge it gradually. This approach is particularly helpful with ABS frame parts and thin armour found on many Real Grade kits.

Drill Slowly And Check Often

Hold the pin vise like a pencil and keep the shaft perpendicular to the surface. Rotate it between your fingers with light pressure, clearing plastic dust regularly. Several shallow turns are safer than forcing the bit through in one movement. Stop frequently to check the depth and alignment.

For a hole that must pass completely through a part, place masking tape on the drill bit as a depth marker. Blind holes require extra care: measure the peg or rod, then mark a safe drilling depth that leaves enough plastic behind it. A stop collar or a second layer of tape can prevent an expensive mistake.

If the bit starts wandering, withdraw it and reset the indentation rather than correcting the angle with force. Acrylic paint, primer, or topcoat can slightly reduce an existing opening, so test-fit the accessory after each small adjustment. A loose hole can sometimes be corrected with a tiny amount of plastic cement or thin cyanoacrylate, but an oversized opening is much harder to disguise.

Match The Hole To The Accessory

Different additions need different openings and fitting methods. Brass thrusters and metal pipes may use a straight socket, while photo-etched vents often sit in a shallow recess and need a flat ledge rather than a deep hole. Dry-fit every component before applying adhesive, especially when the part will be painted separately.

Addition Typical preparation Useful caution
Metal rivet 0.3–0.6 mm pilot hole Avoid drilling too close to a panel edge
Brass rod Hole matching rod diameter Test depth before gluing
Metal thruster Gradually enlarged socket Keep the opening centred
Photo-etched vent Shallow recess or slot File edges instead of forcing the part
Metal pipe Two aligned holes Check the angle from several views

Photo-etched brass is thin and can bend permanently if pushed into a tight opening. Shape it on a hard, flat surface with a smooth tool, then secure it with a small amount of CA glue after painting if the design allows. For a larger customisation project, the Gundam display case is a useful place to compare how builders position vents, thrusters, and exposed mechanical detail.

Prevent Cracks And Surface Damage

Plastic shavings can hide inside armour seams and interfere with assembly. Brush them away with a soft makeup brush or use a hand air blower; avoid blowing directly with your mouth, particularly when working with resin or dusty fillers. A piece of masking tape pressed lightly over the area can lift loose debris without scratching the surface.

Keep separate bits for styrene, ABS, and resin if you modify several materials. Resin can blunt fine drills quickly, while ABS may grab the bit if too much pressure is applied. Do not twist a stuck bit aggressively. Reverse it slowly, inspect the hole, and widen the opening by tiny increments.

When working on a painted kit, protect the surrounding area with low-tack masking tape. A fresh blade can trim raised plastic around a drilled hole, but scrape gently because a deep cut may be more visible than the original fitting. Photographing the part before modification also helps when you need to reassemble an intricate frame.

Recommendations For Cleaner Modifications

  • Use a pilot hole before enlarging any opening.
  • Match the drill bit to the accessory with a calliper or size chart.
  • Support thin armour from behind with foam or removable putty.
  • Mark depth with masking tape when drilling blind holes.
  • Test-fit metal parts before using glue or paint.
  • Keep spare bits in a labelled case to prevent damage and confusion.
  • Work over a tray so tiny photo-etched parts are easier to recover.

Plan The Detail Around The Whole Build

Metal additions look most convincing when they support the kit’s existing structure. Repeated vents, matching rivet sizes, and consistent spacing create a deliberate mechanical language. A single oversized thruster can draw attention away from the silhouette, while a restrained set of small fittings can make armour separation feel more believable.

Consider how the finished model will be displayed before drilling. A custom base may hide lower details or change the viewing angle, so mark the visible sides first. Gundam Eclipse’s diorama base guide offers useful context for planning the relationship between a model, its base, and added mechanical features.

Australian conditions can affect the final result too. Warm summer workspaces in Brisbane or Perth may speed up CA glue curing, while a cooler Melbourne bench can give slightly more working time. Store photo-etched sheets and tiny metal parts in sealed containers, especially if your workspace is near the coast where salty air can encourage tarnishing.

Share your drilled parts, fitting tests, and finished custom details with the Gundam Eclipse community so other builders can see what worked. A clear work-in-progress photo and the bit size used can turn a small modification into practical advice for builders across Australia and beyond.

A member-contributed review of the Moderoid 1/60 SAVAGE CROSSBOW kit, published in the Gundam Eclipse Reviews section. The reviews area hosted 246 topics and roughly 1,400 posts.

PG 00 Gundam

November 4, 2018 — by heathorn

A completed Perfect Grade 00 Gundam build showcased in The Display Case. This section featured approximately 2,200 topics and 24,900 posts, making it one of the forum's largest galleries of finished work.

HG Zeta Gundam Evolution Project

2018 — by kajnrig

An ongoing High Grade Zeta Gundam customization project shared in the Work-in-Progress Thread. This was the most active section on the forum, with roughly 1,400 topics and 34,300 posts where members exchanged feedback and progress updates.