Recolouring a Gundam kit from its original guide
How to swap colors on a kit using the original color guide as a starting point is a practical way to create a custom scheme without losing the designer’s sense of balance. The colour guide already shows which areas are intended to contrast, which panels should recede, and where small accents can add visual interest.
For Australian builders, this approach also helps control paint use and avoid unnecessary experimentation. Whether you are working at a Sydney club table, in a Melbourne hobby room, or around the humidity of Brisbane, a planned palette makes the build cleaner, easier to troubleshoot and more enjoyable to share on Gundam Eclipse.
Read the guide as a design map
Start by separating the kit’s colours into roles rather than treating every shade as an isolated choice. The largest area is usually the main armour colour, followed by a secondary colour for limbs or structural panels. Dark grey, navy or black often provides visual weight, while yellow, red or another bright tone acts as a small highlight.
Photograph or scan the instruction manual colour page, then mark each section with a simple code: A for the dominant colour, B for the supporting colour, C for frame or joint details, and D for accents. This is particularly helpful on Real Grade kits, where layered armour can make a small colour change appear across several separate runners.
Before cutting parts, inspect the plastic colours and mould separation. A red section may be split into multiple pieces, while a grey detail might be moulded together with a larger panel. The original colour guide reveals the intended result, but the physical part layout determines how easily you can reproduce or alter it.
Build a controlled custom palette
Choose replacements by function. A white-and-blue mobile suit can become cream-and-forest green, for example, while retaining the original light-versus-dark relationship. Changing every colour at once often produces a muddy result, so keep at least one visual anchor from the stock scheme, such as the frame, weapon, sensor or signature accent.
Make spoon tests or paint swatches before committing to armour parts. Compare the samples under both indoor lighting and daylight, since Australian sun can make colours look considerably brighter than they appeared under a desk lamp. Local shops such as Hobbyco and Metro Hobbies can be useful for comparing paint ranges in person, while online orders give access to specialist lacquer and acrylic shades.
Keep a written mix ratio for custom colours and label each jar. A scheme that looks excellent on a shoulder still needs to match across the shield, knees and backpack. If a colour requires several coats, record whether the sample was applied over grey, white or black primer, because the undercoat will change the final appearance.
Compare the scheme before full painting
Use masking tape, removable tack or digital editing to preview the proposed layout. The purpose is to check colour distribution, not to create a perfect render. Look at the kit from the front, side and rear, because a balanced chest can still leave the backpack or legs visually too heavy.
| Original role | Safe colour change | What to watch |
|---|---|---|
| Main armour | Cream, olive, deep blue or warm grey | Keep the largest surfaces consistent |
| Secondary armour | Muted red, pale grey or contrasting blue | Avoid competing with the main colour |
| Frame and joints | Charcoal, gunmetal or dark brown | Preserve mechanical depth |
| Small accents | Orange, yellow, teal or white | Use sparingly for emphasis |
| Weapons | Neutral grey, black or desaturated colour | Separate them from the body |
Build a single test section before painting the complete mobile suit. A torso or lower leg usually contains enough surface area to judge the relationship between adjacent panels. Builders working on complex kits can also review RG Hi-Nu solutions for reminders about fit, layered armour and handling delicate construction.
Paint cleanly and protect the finish
Disassemble the kit as far as practical, wash away mould-release residue and lightly test-fit parts before priming. Sanding seam lines should happen before the colour coats, while masking edges need a firm, clean surface. On ABS joints and moving sections, use compatible products carefully and avoid building thick paint where parts rub.
Keep the work area organised with separate trays for painted armour, frame pieces and untouched parts. A small batch-painting system is efficient: prime related pieces together, apply the main colour, add shadows or highlights, then mask for the next colour. Two or three thin coats generally preserve panel detail better than one heavy coat.
Useful controls during the painting stage include:
- Use low-tack tape for sharp armour boundaries
- Protect polycaps and tight joints from paint buildup
- Test lacquer, enamel and acrylic compatibility first
- Let each coat cure before handling or masking
Before applying decals, decide whether the scheme needs a gloss, satin or matt surface. Decals settle more cleanly over gloss, while a final flat finish can unify mismatched sheen. Gundam Eclipse’s guide to topcoat finishes explains why the protective layer should be treated as part of the finishing plan rather than an afterthought.
Share the result and refine the idea
Photograph the completed kit against a neutral background, using soft daylight where possible. Avoid strong midday sun through a window, which can wash out pale colours and create harsh reflections. A simple front, rear and three-quarter set gives other builders enough information to assess the palette and construction.
When posting to the Display Case, include the original kit, the colour changes, paint brands and any unusual preparation steps. Australian members may be especially interested in how a scheme behaved during a humid Brisbane summer or a dry Melbourne winter, since curing times and spray conditions can vary widely.
- Mention the original guide’s colour roles
- Identify custom mixes and primer colours
- Show close-ups of masked boundaries
- Note changes made after test fitting
A strong recolour is a conversation starter, not just a finished photograph. Post your build to Gundam Eclipse, explain the decisions behind the palette, and use the community’s feedback to develop the next custom scheme.