Custom acrylic colour mixing for Gundam model builders
Mixing your own custom paint colours from basic acrylics gives a Gunpla project a more personal finish without requiring a shelf full of specialised bottles. A small selection of white, black, primary colours and a few earth tones can produce most shades needed for armour, joints, weapons and scenery.
The key is controlled experimentation. Acrylic paint can shift noticeably as it dries, and Australian conditions add their own variables: a humid Brisbane day, a dry Adelaide afternoon or cool weather in Melbourne can all affect thinning and drying time. Keep notes, work in small batches and test every colour before it reaches the model.
| Target colour | Starting mix | Useful adjustment |
|---|---|---|
| Pale blue armour | 3 parts white, 1 part blue | Add a touch of grey to reduce brightness |
| Warm grey | 4 parts white, 1 part black, tiny red touch | Add ochre for a dusty tone |
| Olive green | 3 parts yellow, 1 part blue, small black touch | Add brown for military warmth |
| Rust orange | 2 parts red, 1 part yellow, tiny black touch | Add more red for darker oxidation |
| Gunmetal | 3 parts black, 1 part blue, small white touch | Add metallic medium if available |
Build a useful colour palette
Start with artist acrylics or hobby paints in cyan or blue, magenta or red, yellow, white and black. A warm brown, neutral grey and dark green are worthwhile additions because they make muted military colours much easier to achieve. Pure black can make a mix look flat, so dark blue or brown often creates a more convincing shadow colour.
Use a ceramic palette, tile or disposable mixing tray rather than cardboard, which absorbs water and pigment. A couple of inexpensive brushes, pipettes and mixing sticks help keep proportions consistent. If you are shopping at Bunnings for general tools, remember that hardware-store acrylics are usually too coarse for fine Gunpla work; specialist hobby shops and Australian online model retailers are safer choices for smooth pigment.
When mixing custom paint colours, think in ratios rather than vague drops. “Three parts white to one part blue” can be repeated, enlarged or reduced, while “a little blue” is difficult to recreate later.
Measure, swatch and record
Place small paint portions beside one another and mix only enough for a test spoon, spare runner or plastic spoon. Let the swatch dry fully before judging it. Acrylics often dry slightly darker or less saturated, particularly when diluted for an airbrush or brush-painted in thin layers.
Keep a notebook or phone record with the brand, colour names, ratio, thinner and finish. Australian hobbyists may find this especially useful when ordering from interstate shops, because a replacement bottle can take several days to arrive. A labelled dropper bottle is ideal for storing a successful mix, though add a mixing ball and shake it thoroughly before use.
For a neutral comparison, place swatches beside the kit under the light where it will be displayed. A colour that looks right beneath a cool LED bench lamp may appear too green under warm household lighting. If you are building a desert scene inspired by Woomera or the Pilbara, slightly warm the shadows with ochre or brown rather than using plain black.
Control opacity and surface finish
White is the most useful colour for creating highlights, but adding too much can make a shade chalky. Mix a mid-tone first, then create lighter and darker variations from that base. This gives the armour panels a coherent family of colours while still providing contrast between large surfaces and small details.
Thin acrylics gradually with the manufacturer’s thinner or a small amount of distilled water. Tap water can work, but mineral-heavy water may leave a rougher finish or interfere with consistency. In dry climates such as Perth or inland New South Wales, paint can dry on the palette rapidly, so a damp palette and smaller working amounts are practical. In tropical Queensland, use less thinner and allow extra curing time between coats.
For a satin or semi-gloss result, mix in the appropriate medium rather than relying on extra water. Metallic acrylics also benefit from a smooth gloss-black base. Keep metallic tools separate where possible, since stray flakes can contaminate flat colours.
Match colour to the build
A custom colour should support the whole model, not just look attractive in the mixing cup. For a military mobile suit, desaturate bright primary colours with grey, brown or their complementary colour. Red can be softened with a small amount of green, while yellow becomes more realistic with brown or a trace of purple.
Before painting, prepare the surface carefully. A clean primer coat reveals whether the mix is too transparent, too thick or uneven. Fine surface work can make a greater difference than a perfect formula, so consider pin-vise drilling for vents and gun barrels before applying your colour scheme.
For a display scene, coordinate the model with its base. Dusty tan, concrete grey and oxidised orange can be mixed from simple colours, then varied across separate panels to avoid a toy-like finish. The techniques in this foam-board diorama base guide can help you plan those surrounding tones before committing to the kit.
A practical mixing checklist
Use this routine whenever a new shade is needed:
- Begin with the lightest colour and add darker pigment a tiny amount at a time.
- Mix more paint than the first panel requires, especially when covering multiple armour sections.
- Test both a thick brush coat and a thinned coat on spare plastic.
- Label successful mixes with ratios, paint brands and the date.
- Keep a lighter and darker version for highlights, panel variation and shadows.
- Check the dried colour under the display lighting before continuing.
- Seal finished paint only after it has cured properly.
Small colour differences can make a Gundam feel more mechanical and layered. For flight poses, plan the palette around the support as well as the mobile suit; transparent supports should remain visually quiet, as shown in this guide to clear flight rods.
Share your colour recipes, dried swatches and lessons learned on Gundam Eclipse. A simple ratio that works in a Sydney flat, a Canberra garage or a Darwin hobby room may save another builder time and help turn basic acrylics into a genuinely distinctive build.